Went along to assist a local club set out the track for a moto x race meeting on Sunday and was invited to join in! Apparently you can get a one day competition licence, but I won't be taking up the offer, I had enough fun tearing round the track after it was set out.
Hello All. I thought I'd finally introduce myself here as I've been floating around for a while soaking up all the info in the maintenance threads. i bought a 99 TTR 250 Raid back in April and have already had a few experiences I thought I would share! Firstly, great bike and made even better by a very inf...
Hi all was wondering if any one had or knew of anyone selling a rear exhaust box for the blue ttr 250? many thanks Tom -- Edited by Tucker250 on Wednesday 24th of July 2013 11:31:07 PM
Just wondering if it's possible to use the gauges from an XT350 (speedo at least). I know you guys can use xt225 gauges, but how do you hook up a speedo cable to the front hub if your blue model only has the Yamaha odometer? Just saying cause I got to ride a 1990 xt350 and I liked it. Thanks! -- Edited by yamaha...
Hi All Firstly, although this isn't a ttr related problem, I'm hoping an electrical wizard will be able to help me figure out where I am going wrong! My DR350 got stolen a few weeks back. By some miracle the police managed to recover it after seeing some kids wheeling it about outside a travellers site....
Has there ever been any comment on the 280 kit's performance? I found the bit in Brian's thread about the OE's resto but then the trail runs cold? I'd like to know what's involved-cost & time and the results Anyone know? Mark
I have sourced a few pairs of new original Yamaha TTR250 mirrors. These have the correct left and right hand threads to fit into the existing sockets on your clutch and brake perches. They will also fit WRFs and WR250R/Xs It's a personal choice as to whether to to run mirrors but I like to keep an eye on who...
Hey guys, The majority of riding I do is real tight steep 1st gear mountain trails, I find I am needing more revs than are practical at these slow speeds and thinking about changing my sprocket to give me more revs/grunt down low. I have standard 14 and 44 tooth setup at the moment and my question is i...
Got fed up of old ****ty tank stickers that were on the bike when I bought her, so set too and stripped them off and look what I found underneath, original laquered on tank stickers, before and after shots Off to the Isle of Man green laning next Thursday till sunday night, miles and milesof them over ther...
These discs aren't wearing as well off tarmac as the other discs we sell. We have just two left in stock after which we won't be stocking them again as most of our customers use their TTR off tarmac at some point. They are on offer at a bargain price of £42 plus p&p See here Email sales@totallyttrs.co...
2006 Low Mileage Yamaha TTR250 For SaleRare opportunity to buy a Yamaha TTR250 trail bike that has had a frame up rebuild! Reliable and economical 250cc four stroke with 6 gears- the perfect dual purpose commuter/trail bike.First registered March 2006.MOT (full MOT – not a “daylight"...
Time for me to ask the dumb question, I brought a FMF Q4 silencer (not sure why now) it was a bit noisy but I fitted a piece of perforated stainless pipe with a blanked off end inside the back of the silencer and it works fine but I suspect I need to change the carb settings (although the bike runs ok). Any ide...
For sale my 2004 ttr 250 2950 miles from new taxed and tested untill Dec 2013,new chain and sprocket only done 400 miles since,sprockets 13/50 I think will have to check.motad silencer and ali sump guard fitted all purchased from Brian.fitted K&N air filter and mesh oil filter.could do with a set...
I went to adjust my needle and I realized the washer with the locking tab that sits below the needle clip is missing Is this a universal part? It must be a specific thickness because it holds up the needle im guessing. In THIS diagram, it's the part just below the needle in section 6. It is sitting right...
Hello all, I have begun my Rallye build for the Australian 2012 APC Rally . Ill be using my wifes 1999 TTR 250 for my build along with a rolling 2000 TTR 250 that I have recently acquired. The APC rally runs for 14 days covering a distance of 7100km. Navigation is via GPS. All riders have to ca...
Carb sat with fuel in it for about a year. Of course the gas went bad and gummed it up. I tore it apart and cleaned it. First start it ran extremely lean. Bike had no power and would cut out above quarter throttle. Tore it down again and did a better job of cleaning it. Jets appear to be clear. Put it back togeth...
my bike fell on to its left hand side in the van, only damage was a cracked fr. left indicator lens and a smashed bulb. standard indicators. i replaced the bulb but it now flashes about 20 times a second???? the right hand side is ok,when i put the hazards on all 4 flash perfectly.? i'm not electrically min...
Hi. The previous owner of my bike had the tank re-sprayed to a good standard, however he tried to apply the 'standard' TTR stickers to each side and it didn't go so well! They are also now peeling at the front as well and would like to replace them. I like the 'retro' 80's colours and would like to stick w...
Still having running light issues. Changed company he long life 1157 bulb. As told to do. Got my hands on a multimeter. Bike keyed on headlight on bike not riding -11.64 both running and with foot engaging brake 13.6 bike idling 13.6 bike in high iam am going to replace wires that I addEd to get the h...
This is, hopefully, going to be a simple restoration of a 2006 TTR to as near new standard condition as I sensibly can. The before pics look better than the the bike originally was when I bought it as I forgot to take pics before power washing it, fitting a legal exhaust, side panels, plus fitting a headli...
Trimmed the airbox snorkel inlet. As anticipated, the fuel screw was turned out to compensate (out about 3.75 turns now). The a$$ dyno feels a slightly stronger pull on bottom, but sort of falls off up top. Any Comments or concerns? I'm running an UNI air filter with a Mikuni vm28/486 42.5 pilot and a n1...
Hi, My name is Nige and I am based in Plymouth, Devon. I have recently bought a R reg White OE from Mike Wright on this forum and am enjoying it, although it needs a little tweek as he told me when I bought it. Never done any Trial Riding before as I have always had big toys like 1250 Bandits, BMW R1150R's etc, b...
I have a TTR & XT660R both running on 520 chain, as I use the XTR off road I use x3 front sprockets 13,14,15. I had been running on a 14 front but decided to fit a new 15 t front before going out with friends to the 'Cassington bike night 2013' (look it up, it's brill, 10,000 bikes in a small Cotswold villag...
Is there anywhere that has longer clutch cables or is there a cable from another bike that's longer & will fit the TTR... need about 75mm longer.. Just fitted fat bars & risers...
Hello, My 2004 ttr has developed a rattle. Its actually more of a jingle that happens when the engine is not under load. I wondered if it could be the clutch plates having worn tabs but any thoughts would be welcome before dismantling anything. Thanks Alex
-- Edited by Tucker250 on Wednesday 24th of July 2013 11:31:07 PM
