This guide shows how to replacing the steering head bearings with new using an AllBalls kit Firstly remove the old outer bearing races. I used a special tool made for the job. An alternative way of removing an outer bearing race which will be scrap is to put a blob of weld on its surface from an arc weld...
Hello, As I have just explain in my presentation, I bought a 93's TTR250 last saturday and I m starting to check the parts which need to be replace. The first one is the rubber pipe between the carburator and the cylinder;, it is completely worn and probably creates an air leak wich can explain why the en...
The original bolt cap can be easily damaged. so as alternative i found cheap backup bolt from mother china. seems to fit ok -- Edited by honda15i on Wednesday 15th of May 2019 08:28:45 PM
These Yamaha top bearings does not last long. Every season I need to replace them. I found alternative top bearing from Germany for the cost of 15€. It is 1 or 2 mm narrower than original, but in double less price than yamaha's. Fits perfectly. Bearing code for googling - GXSW 12.26 Adding photos (comp...
Hi I have recently had the sprag clutch on My TTR replaced as there was a noise when you switched the bike off. The mechanic that did the job said there was significant wear on the sprag you could rotate it both ways before it would lock up. The Boss gear he said had a little bit of wear but he didn't think it w...
Hi all, I have a couple of questions relating to the TTR gearbox, hopefully the collective genius of the forum can help me! I've had a couple of occasions recently where I get stuck in first gear. Gear changes on the low gears can also tend to seem very stiff / like they are not engaging properly. Higher ge...
got my quote from carol nash last week for my 3 bike policy very expensive tried to ring them twice left on hold both times for about 30/35 minuites tried next day 20 mins then some one answered said i had come through to wrong department put on hold again 15 mins then he told me some one would ring me back in h...
Hello guys new to this but having a little problem with my new to me 2006 ttr 250. Its four stroke. and the problem is it starts like a dream with the electric starter... But when i get into sticky situations and use kick starter it wont start bike.... It will engage but will not give enough umph to actuall...
i have three TTRs. When I sit on one i noticed its higher then others i.e seat and ground clearence. i tried to find the difference, i replaced rear shock absorber to another ttr but it didn't make any difference. then after some time i wanted to change worn rear tire. The tires are the difference! pirell...
one of mine ttrs bogs on high rpm around 6500-7000. It seems like I hit rpm limiter, engine doesn’t reach full power. My second TTR reach top high rpm without bogging. I took these parts from second ttr and installed on first: 1. Carb with fuel hoses and one way valves 2. Cdi 3. Ignition coil 4. Spark plug 5...
Does anyone know of upcoming or recurring adventure, dual sport, or enduro rides along or near the Atlantic Coast of the United States? There are a few harescramble and cross country races and series but I'm looking for a more casual riding event rather than competition. This type of event usually re...
Google translator If I put the ttr on the right side, can I unscrew the oil plug? Does the oil leak? I want to replace the copper pad because I have a leak.
Hi, I'm not a fan of Chinese items however it happened I have head and cylinder gaskets for price of 7£. The head gasket is very thin and without teflon. Yamaha gasket I think has two or three gaskets stamped and painted with teflon. Has anybody tried chinese gaskets? See photos. -- Edited by honda15i on...
Hi allI am out in Wales at the moment, riding my Wr250f for this trip, with my mates. Garry from Ireland and Mark from Somerset on their ttrs. Me and Chris on wrf and crf, both our ttrs were not able to make it here is a nice photo for now, will add a write up later -- Edited by ttr steve on Sunday 5th of May 20...
A led headlight arrived in the mail today it's much the same size as my TTR one but will need brackets made to fit Will let you know how it goes I like the plastic lens and straight h4 plug in 45watt led -- Edited by ttboof on Tuesday 29th of January 2019 11:52:35 PM
Ok I messed up! Somehow I managed to damage the thread in the float bowl for the drain screw. I must have put it in cross threaded. I the drain screw itself is damaged but more worryingly is the thread inside the bowl. Any suggestion what to do? Rob
Hi Anyone knows if a stator from a later model wold fit? IE the year 1999? Having problems finding av stator for my bike from 1994. Thanks Per Arne Bustnes Norway
Hi All I recently bought a TTR250 that was imported to Madagascar from Europe about 10 years ago. Before last week I knew nothing of TTR's. I noticed that mine has no indicator lights nor brackets to accommodate them. It does, however, have an indicator switch on the handlebar. I don't have any of the o...
here is a nice photo for now, will add a write up later 