A forum for owners of Yamaha TTR250 trail and enduro bikes!

davecambo · davecambo

http://www.ebay.com/itm/Derestrict-CDI-YAMAHA-TTR250-4GY-Ignitor-Ignition-/280698833419?pt=LH_DefaultDomain_100&vxp=mtr&hash=item415af44a0b

davecambo · davecambo

http://www.torpedo7.com.au/products/EKCHON0C1/title/ek-chain-520sro-o-ring-chain

davecambo · davecambo

is it normal for fuel to drain out of the tube that leads to what looks like the float bowl when you tip the bike to the left about 45 degrees. i was lubing my chain and had the bike leaned over to make it easier to turn the rear wheel and noticed fuel leaking out.

shack · shack

Hi all, I'm after printing a couple of pages from the downloaded owners manual, but it says it is password protected, anyone shed some light on this? don't think the wife would be impressed if the laptop dissappeared into the garage for an oil change just being lazy and trying to safe myself having to w...

davecambo · davecambo

i am buying a new socket set, and would like to know the largest nut that is on a TTR so i can get a set that will service my bike without having to go parts shopping half way through something. also if the nut is metric or not would be great too. cheers.

davecambo · davecambo

Do you think you would notice a change from 47 to 48 rear sprocket? Just took the bike for a test ride with the 13:47 setup and she went well and still does over 110 km/h. Gearing commander says not much difference in top speed with a change to 48, but would there be a noticeable difference in down low resp...

BM Steve · BM Steve

The manual says to use a 520V2 but the chain below I was wanting to buy It's called a D.I.D 520VT2 T-Ring Chain Link Does anyone know if it's suitable ?? It's on super special this week Thanks Steve

pedrosan · pedrosan

Hi guys, Hope you had a good Christmas. I have been commuting through the snow over a moorland track on my TTR250 ('94 Raid), having a few slips trips and falls on the ice but never being let down by the bike yet. I recently changed my Sprag with parts I sourced from Partshark in America, I did it because I...

davecambo · davecambo

quick question, when riveting master links with a rivet tool (one i just ordered from America) how much do you rivet each pin? as in how wide should the rivet be after being pressed to confidently stop the link from failing. cant find anything on the net. would a mm increase in diameter be enough or too mu...

davecambo · davecambo

can i get some figures on what you guys are getting out of a tank please? those of you with blue, 10L tanks only. doesnt matter what mods you have, the more the merrier, i can just average it all out at the end.

davecambo · davecambo

how big a sprocket can you go on the back before you have to alter/lower the chain guide (if thats what it is called) on the bottom of the swingarm at the back that the chain runs through? im thinking about running 14:50 or 52 setup.

davecambo · davecambo

hi all, i just finished putting on the 47 tooth rear sprocket. already had a 13 on the front. took her for a spin round the block and initialy thought that it may be too short in 1st gear. Any thoughts? reason i put the 47 on was too high top speed. wanted to reduce it a bit and gain more response down low. would...

shack · shack

Hi all, just doing an oil change and found the large 'o' ring around the filter housing has snapped, but can I find a replacement?, the two smaller ones have seen better days as well, but might be able to get these a little easier. Where have (has anyone) people go replacement ones from? or it is worth just...

fatboy686 · fatboy686

Hello all, My newly acquired TTR will be going in for an MoT test next week, but I have one question. The original number plate assembly (regular size plate, reflecter, number plate light) has been replaced by a slightly smaller number plate, with no number plate light and no reflector (it has a red...

davecambo · davecambo

mate any chance of posting a pic of the difference between your great looking footpegs and the standard ones. how much would these be shipped to Australia too mate? cheers!

dan-reeves · dan-reeves

Hello i purchased a fmf silencer for my bike and fitted it on, there dosent seem to be an increase in power, (just louder) was just wondering if anyone has fitted this exhaust and had to re jet it? Also if the exhaust will do any damage to the engine will different back pressure? (was thinking of putting t...

DC · DC

Hi folks. Hosed down after a ride a few weeks ago, put the bike away. Today, no start on the button or kick. Turn over but no fire. I have power, checked the spark, checked fuel is flowing, drained fuel from carb, checked airbox is dry. Removed tank to get at all the electrical connections. Gave them a...

tonyh210367 · tonyh210367

Hi I'm in need of a bashplate and have access to some good fabrication facilities at work. Would any of you be so kind as to take a photo / produce a quick sketch with the key dimensions so I can get one fabricated. I could of course take some measurements myself but thought it better to use a trusted design :...

davecambo · davecambo

hi there again. I have pulled my sparkplug and taken a picture of it. what do you think? it has both black and white parts. just trying to work out if its rich or lean. And while i have you looking, this rubber thing was sitting on top of the engine next to where the spark plug goes. what the hell is it and where...

davecambo · davecambo

hey guys, i got to 200km and changed the oil on my new 2011 TTR. it was very black. i then put spare full synthetic oil i use in my ducati 1100 in the TTR, but have since remembered that this may not be recommended for a new bike like my TTR as it hasnt finished breaking in. I read this is because of glazing in the...

barto · barto

hi any feed back would great i have a ttr 250 06 it has been riden hard 3 day bike rides through country sides still running fine ..very reliable great bike but i have found scrape marks on the clutch housing also it make a metal spinnig noies under duress and also when changeing gear any imfo would be gr...

davecambo · davecambo

i am running 13 front and tomorrow changing to a 47 rear sprocket instead of the 44. will i need new chain?

davecambo · davecambo

after being paid a little more than usual, i now have a budget for a better or more expensive exhaust. staintunes are very good australian built exhausts and for 640 Australian dollars it could be the one i buy. just wondering if any aussies have put one on a blue ttr, even better a late model blue one like...

davecambo · davecambo

can i use castrol race edge oil that i have heaps of at home, or do i have to use yamalube?

tonyh210367 · tonyh210367

Hi All Just a general query to see if anyones aware of any other throttle or clutch cables that fit the TTR. Cheers, Tony

davecambo · davecambo

i think this has been asked already but are there any differences between the 2006 TTR and the 2011 TTR exhaust wise. I have made up my mind and am buying a FMF exhaust, but the company only lists them for models up to 2006. I think this is due to Aus and NZ being the only countries to keep producing them? Obvi...

davecambo · davecambo

just got off the phone with a stockist for fmf here in Australia who said he wasnt sure if adding a fmf powercore 4 slip on would give any improvement other than weight saving. can anyone on this forum that has replaced the muffler only, ie - kept the original header pipe, tell me if there was increase in p...

Abbas · Abbas

Has anybody seen a yoshimura RS 3 full system exhaust fitted on a ttr before, if any body has an experience with it or if there is a full system that is better for the ttr, I don't mind if it was little bit loud. -- Edited by Abbas on Saturday 7th of January 2012 01:30:43 PM

TTRfan · TTRfan

The pics are for Valkman who is looking to improve the rear footpegs on his OE. I can't find a decent pic showing the pegs fitted. Can a Raid owner help out please?

davecambo · davecambo

came accross the brand Lexx exhausts. they are quite cheap here in australia. 270 dollars. Just wondering how they would compare to fmf or similar.

Topic		Started By	Replies	Views	Last Post
	what is this? (Preview) http://www.ebay.com/itm/Derestrict-CDI-YAMAHA-TTR250-4GY-Ignitor-Ignition-/280698833419?pt=LH_DefaultDomain_100&vxp=mtr&hash=item415af44a0b	davecambo	3	1293	Feb 19, 2012 by Cubber
	nice deal on a chain (Preview) http://www.torpedo7.com.au/products/EKCHON0C1/title/ek-chain-520sro-o-ring-chain	davecambo	0	1011	Feb 16, 2012 by davecambo
	fuel leaking when bike tipped over 45 degrees (Preview) is it normal for fuel to drain out of the tube that leads to what looks like the float bowl when you tip the bike to the left about 45 degrees. i was lubing my chain and had the bike leaned over to make it easier to turn the rear wheel and noticed fuel leaking out.	davecambo	2	1209	Feb 16, 2012 by davecambo
	Printing from the owners manual (Preview) Hi all, I'm after printing a couple of pages from the downloaded owners manual, but it says it is password protected, anyone shed some light on this? don't think the wife would be impressed if the laptop dissappeared into the garage for an oil change just being lazy and trying to safe myself having to w...	shack	1	1222	Feb 16, 2012 by Cubber
	largest nut on TTR (Preview) i am buying a new socket set, and would like to know the largest nut that is on a TTR so i can get a set that will service my bike without having to go parts shopping half way through something. also if the nut is metric or not would be great too. cheers.	davecambo	8	1646	Feb 15, 2012 by davecambo
	47 to 48 rear (Preview) Do you think you would notice a change from 47 to 48 rear sprocket? Just took the bike for a test ride with the 13:47 setup and she went well and still does over 110 km/h. Gearing commander says not much difference in top speed with a change to 48, but would there be a noticeable difference in down low resp...	davecambo	0	906	Feb 14, 2012 by davecambo
	What Type Of Chain (Preview) The manual says to use a 520V2 but the chain below I was wanting to buy It's called a D.I.D 520VT2 T-Ring Chain Link Does anyone know if it's suitable ?? It's on super special this week Thanks Steve	BM Steve	11	1965	Feb 14, 2012 by davecambo
	Sprag and Gaskets (Preview) Hi guys, Hope you had a good Christmas. I have been commuting through the snow over a moorland track on my TTR250 ('94 Raid), having a few slips trips and falls on the ice but never being let down by the bike yet. I recently changed my Sprag with parts I sourced from Partshark in America, I did it because I...	pedrosan	10	1902	Feb 14, 2012 by pedrosan
	riveting chain master links (Preview) quick question, when riveting master links with a rivet tool (one i just ordered from America) how much do you rivet each pin? as in how wide should the rivet be after being pressed to confidently stop the link from failing. cant find anything on the net. would a mm increase in diameter be enough or too mu...	davecambo	1	1011	Feb 13, 2012 by Cubber
	milage (Preview) can i get some figures on what you guys are getting out of a tank please? those of you with blue, 10L tanks only. doesnt matter what mods you have, the more the merrier, i can just average it all out at the end.	davecambo	4	1578	Feb 12, 2012 by Cubber
	how big can you go on the back (Preview) how big a sprocket can you go on the back before you have to alter/lower the chain guide (if thats what it is called) on the bottom of the swingarm at the back that the chain runs through? im thinking about running 14:50 or 52 setup.	davecambo	0	996	Feb 11, 2012 by davecambo
	13:47 too short? (Preview) hi all, i just finished putting on the 47 tooth rear sprocket. already had a 13 on the front. took her for a spin round the block and initialy thought that it may be too short in 1st gear. Any thoughts? reason i put the 47 on was too high top speed. wanted to reduce it a bit and gain more response down low. would...	davecambo	0	1154	Feb 11, 2012 by davecambo
	sourcing rubber o rings (Preview) Hi all, just doing an oil change and found the large 'o' ring around the filter housing has snapped, but can I find a replacement?, the two smaller ones have seen better days as well, but might be able to get these a little easier. Where have (has anyone) people go replacement ones from? or it is worth just...	shack	5	2679	Feb 10, 2012 by shack
	Quick MoT test question .... (Preview) Hello all, My newly acquired TTR will be going in for an MoT test next week, but I have one question. The original number plate assembly (regular size plate, reflecter, number plate light) has been replaced by a slightly smaller number plate, with no number plate light and no reflector (it has a red...	fatboy686	4	967	Feb 9, 2012 by fatboy686
	another one for TTR fan (Preview) mate any chance of posting a pic of the difference between your great looking footpegs and the standard ones. how much would these be shipped to Australia too mate? cheers!	davecambo	2	867	Feb 9, 2012 by Cubber
	FMF powercore 4 exhaust (Preview) Hello i purchased a fmf silencer for my bike and fitted it on, there dosent seem to be an increase in power, (just louder) was just wondering if anyone has fitted this exhaust and had to re jet it? Also if the exhaust will do any damage to the engine will different back pressure? (was thinking of putting t...	dan-reeves	5	2517	Feb 9, 2012 by davecambo
	Won't start after a hose down.. (Preview) Hi folks. Hosed down after a ride a few weeks ago, put the bike away. Today, no start on the button or kick. Turn over but no fire. I have power, checked the spark, checked fuel is flowing, drained fuel from carb, checked airbox is dry. Removed tank to get at all the electrical connections. Gave them a...	DC	14	2224	Feb 9, 2012 by TTRfan
	Bashplate Dims Required Please (Preview) Hi I'm in need of a bashplate and have access to some good fabrication facilities at work. Would any of you be so kind as to take a photo / produce a quick sketch with the key dimensions so I can get one fabricated. I could of course take some measurements myself but thought it better to use a trusted design :...	tonyh210367	0	952	Feb 6, 2012 by tonyh210367
	take a look at this please (Preview) hi there again. I have pulled my sparkplug and taken a picture of it. what do you think? it has both black and white parts. just trying to work out if its rich or lean. And while i have you looking, this rubber thing was sitting on top of the engine next to where the spark plug goes. what the hell is it and where...	davecambo	3	1088	Feb 5, 2012 by davecambo
	break in oil (Preview) hey guys, i got to 200km and changed the oil on my new 2011 TTR. it was very black. i then put spare full synthetic oil i use in my ducati 1100 in the TTR, but have since remembered that this may not be recommended for a new bike like my TTR as it hasnt finished breaking in. I read this is because of glazing in the...	davecambo	2	1542	Feb 4, 2012 by davecambo
	clutch houesing has scrape marks on outer edge (Preview) hi any feed back would great i have a ttr 250 06 it has been riden hard 3 day bike rides through country sides still running fine ..very reliable great bike but i have found scrape marks on the clutch housing also it make a metal spinnig noies under duress and also when changeing gear any imfo would be gr...	barto	2	1448	Feb 4, 2012 by barto
	will adding a 47 tooth rear sprocket need bigger chain (Preview) i am running 13 front and tomorrow changing to a 47 rear sprocket instead of the 44. will i need new chain?	davecambo	3	1775	Feb 3, 2012 by davecambo
	staintune (Preview) after being paid a little more than usual, i now have a budget for a better or more expensive exhaust. staintunes are very good australian built exhausts and for 640 Australian dollars it could be the one i buy. just wondering if any aussies have put one on a blue ttr, even better a late model blue one like...	davecambo	3	1460	Feb 3, 2012 by davecambo
	can i use castrol? (Preview) can i use castrol race edge oil that i have heaps of at home, or do i have to use yamalube?	davecambo	1	1937	Feb 2, 2012 by Cubber
	Clutch and Throttle Cables - Any other models fit? (Preview) Hi All Just a general query to see if anyones aware of any other throttle or clutch cables that fit the TTR. Cheers, Tony	tonyh210367	1	947	Feb 1, 2012 by Cubber
	is a 2006 the same as a 2011 (Preview) i think this has been asked already but are there any differences between the 2006 TTR and the 2011 TTR exhaust wise. I have made up my mind and am buying a FMF exhaust, but the company only lists them for models up to 2006. I think this is due to Aus and NZ being the only countries to keep producing them? Obvi...	davecambo	2	1062	Jan 31, 2012 by davecambo
	fmf slip on ONLY (Preview) just got off the phone with a stockist for fmf here in Australia who said he wasnt sure if adding a fmf powercore 4 slip on would give any improvement other than weight saving. can anyone on this forum that has replaced the muffler only, ie - kept the original header pipe, tell me if there was increase in p...	davecambo	2	1203	Jan 31, 2012 by davecambo
	Yoshimura RS 3 exhaust on (Preview) Has anybody seen a yoshimura RS 3 full system exhaust fitted on a ttr before, if any body has an experience with it or if there is a full system that is better for the ttr, I don't mind if it was little bit loud. -- Edited by Abbas on Saturday 7th of January 2012 01:30:43 PM	Abbas	3	2576	Jan 31, 2012 by davecambo
	Pics to show location of rear footpeg mounts on a Raid (Preview) The pics are for Valkman who is looking to improve the rear footpegs on his OE. I can't find a decent pic showing the pegs fitted. Can a Raid owner help out please?	TTRfan	3	995	Jan 30, 2012 by spud351
	lexx exhaust (Preview) came accross the brand Lexx exhausts. they are quite cheap here in australia. 270 dollars. Just wondering how they would compare to fmf or similar.	davecambo	5	1936	Jan 30, 2012 by Metalbender
«First < 1 … 60 61 62 63 64 … 66 > Last» \| Page of 66 sorted by