A forum for owners of Yamaha TTR250 trail and enduro bikes!

davecambo · davecambo

quick question, when riveting master links with a rivet tool (one i just ordered from America) how much do you rivet each pin? as in how wide should the rivet be after being pressed to confidently stop the link from failing. cant find anything on the net. would a mm increase in diameter be enough or too mu...

davecambo · davecambo

can i get some figures on what you guys are getting out of a tank please? those of you with blue, 10L tanks only. doesnt matter what mods you have, the more the merrier, i can just average it all out at the end.

davecambo · davecambo

how big a sprocket can you go on the back before you have to alter/lower the chain guide (if thats what it is called) on the bottom of the swingarm at the back that the chain runs through? im thinking about running 14:50 or 52 setup.

davecambo · davecambo

hi all, i just finished putting on the 47 tooth rear sprocket. already had a 13 on the front. took her for a spin round the block and initialy thought that it may be too short in 1st gear. Any thoughts? reason i put the 47 on was too high top speed. wanted to reduce it a bit and gain more response down low. would...

shack · shack

Hi all, just doing an oil change and found the large 'o' ring around the filter housing has snapped, but can I find a replacement?, the two smaller ones have seen better days as well, but might be able to get these a little easier. Where have (has anyone) people go replacement ones from? or it is worth just...

fatboy686 · fatboy686

Hello all, My newly acquired TTR will be going in for an MoT test next week, but I have one question. The original number plate assembly (regular size plate, reflecter, number plate light) has been replaced by a slightly smaller number plate, with no number plate light and no reflector (it has a red...

davecambo · davecambo

mate any chance of posting a pic of the difference between your great looking footpegs and the standard ones. how much would these be shipped to Australia too mate? cheers!

dan-reeves · dan-reeves

Hello i purchased a fmf silencer for my bike and fitted it on, there dosent seem to be an increase in power, (just louder) was just wondering if anyone has fitted this exhaust and had to re jet it? Also if the exhaust will do any damage to the engine will different back pressure? (was thinking of putting t...

DC · DC

Hi folks. Hosed down after a ride a few weeks ago, put the bike away. Today, no start on the button or kick. Turn over but no fire. I have power, checked the spark, checked fuel is flowing, drained fuel from carb, checked airbox is dry. Removed tank to get at all the electrical connections. Gave them a...

tonyh210367 · tonyh210367

Hi I'm in need of a bashplate and have access to some good fabrication facilities at work. Would any of you be so kind as to take a photo / produce a quick sketch with the key dimensions so I can get one fabricated. I could of course take some measurements myself but thought it better to use a trusted design :...

davecambo · davecambo

hi there again. I have pulled my sparkplug and taken a picture of it. what do you think? it has both black and white parts. just trying to work out if its rich or lean. And while i have you looking, this rubber thing was sitting on top of the engine next to where the spark plug goes. what the hell is it and where...

davecambo · davecambo

hey guys, i got to 200km and changed the oil on my new 2011 TTR. it was very black. i then put spare full synthetic oil i use in my ducati 1100 in the TTR, but have since remembered that this may not be recommended for a new bike like my TTR as it hasnt finished breaking in. I read this is because of glazing in the...

barto · barto

hi any feed back would great i have a ttr 250 06 it has been riden hard 3 day bike rides through country sides still running fine ..very reliable great bike but i have found scrape marks on the clutch housing also it make a metal spinnig noies under duress and also when changeing gear any imfo would be gr...

davecambo · davecambo

i am running 13 front and tomorrow changing to a 47 rear sprocket instead of the 44. will i need new chain?

davecambo · davecambo

after being paid a little more than usual, i now have a budget for a better or more expensive exhaust. staintunes are very good australian built exhausts and for 640 Australian dollars it could be the one i buy. just wondering if any aussies have put one on a blue ttr, even better a late model blue one like...

davecambo · davecambo

can i use castrol race edge oil that i have heaps of at home, or do i have to use yamalube?

tonyh210367 · tonyh210367

Hi All Just a general query to see if anyones aware of any other throttle or clutch cables that fit the TTR. Cheers, Tony

davecambo · davecambo

i think this has been asked already but are there any differences between the 2006 TTR and the 2011 TTR exhaust wise. I have made up my mind and am buying a FMF exhaust, but the company only lists them for models up to 2006. I think this is due to Aus and NZ being the only countries to keep producing them? Obvi...

davecambo · davecambo

just got off the phone with a stockist for fmf here in Australia who said he wasnt sure if adding a fmf powercore 4 slip on would give any improvement other than weight saving. can anyone on this forum that has replaced the muffler only, ie - kept the original header pipe, tell me if there was increase in p...

Abbas · Abbas

Has anybody seen a yoshimura RS 3 full system exhaust fitted on a ttr before, if any body has an experience with it or if there is a full system that is better for the ttr, I don't mind if it was little bit loud. -- Edited by Abbas on Saturday 7th of January 2012 01:30:43 PM

TTRfan · TTRfan

The pics are for Valkman who is looking to improve the rear footpegs on his OE. I can't find a decent pic showing the pegs fitted. Can a Raid owner help out please?

davecambo · davecambo

came accross the brand Lexx exhausts. they are quite cheap here in australia. 270 dollars. Just wondering how they would compare to fmf or similar.

davecambo · davecambo

as the title suggests, i messed with my mixture on the carb and now it goes a bit like a pig. I tired the whole thing of warming it up, then adjusting the idle speed to a little higher, then turning the mixture to the right until it almost conks out, then turning it to the left till it sounds better, but while r...

Cubber · Cubber

Why run around with a bare rear suspension reservoir? If you loosen the hose clips and free the reservoir you CAN wrap a cover round it. You CAN also drink the contents before cutting the CAN as required.

Cheers ...... Martyn

davecambo · davecambo

just wondering if someone could explain why someone would remove the whole snorkel, when technically wouldnt removing ONLY the bottom half that isnt visible from the outside of the air box give more breathability, whilst keeping the curve on the outside to deter water? im thinking that having only...

davecambo · davecambo

Can anyone provide me with a part number for a few decent options for air filters please.

jasparach · jasparach

Hi all, i have a white ttr and and i will need to rebuild the engine. I have two crankcases left and right that i bought from Brian sometime ago as the spring return post broke on mine and my question is do i need anything special in the way of tools to remove the crankshaft from mine to refit to the new crankc...

davecambo · davecambo

gday guys, just thought i would ask people what options i have for adding a better exhaust system to the TTR250. I have a 2011 model, and noticed that there are lots of FMF exhausts on ebay, but they all say they fit models up to 2006. will these fit the 2011 model also? If so, what can i expect from an exhaust...

yamahaTT250R · yamahaTT250R

Hello again, ok i have owned my ttr250 for 3 1/2 years and i just want to know something, When i blip the throttle really fast when idling it bogs, Is this a normal occurance? or it is the jetting, It has a standard 147 main jet (aussie) and 52.5 pilot jet, and a Fmf powercore 4 exhaust, it seems to be running r...

shack · shack

Now I have seen a rather fancy all singing and dancing Bash plate/ sump guard on recent trip to TTR Towers, but wondered if any other guards fit (have seen an XT500 guard going cheap) has anyone had any joy with other OEM gaurds fitting, or being easily adapted? Piccies always a bonus.

Topic		Started By	Replies	Views	Last Post
	riveting chain master links (Preview) quick question, when riveting master links with a rivet tool (one i just ordered from America) how much do you rivet each pin? as in how wide should the rivet be after being pressed to confidently stop the link from failing. cant find anything on the net. would a mm increase in diameter be enough or too mu...	davecambo	1	814	Feb 13, 2012 by Cubber
	milage (Preview) can i get some figures on what you guys are getting out of a tank please? those of you with blue, 10L tanks only. doesnt matter what mods you have, the more the merrier, i can just average it all out at the end.	davecambo	4	1333	Feb 12, 2012 by Cubber
	how big can you go on the back (Preview) how big a sprocket can you go on the back before you have to alter/lower the chain guide (if thats what it is called) on the bottom of the swingarm at the back that the chain runs through? im thinking about running 14:50 or 52 setup.	davecambo	0	748	Feb 11, 2012 by davecambo
	13:47 too short? (Preview) hi all, i just finished putting on the 47 tooth rear sprocket. already had a 13 on the front. took her for a spin round the block and initialy thought that it may be too short in 1st gear. Any thoughts? reason i put the 47 on was too high top speed. wanted to reduce it a bit and gain more response down low. would...	davecambo	0	907	Feb 11, 2012 by davecambo
	sourcing rubber o rings (Preview) Hi all, just doing an oil change and found the large 'o' ring around the filter housing has snapped, but can I find a replacement?, the two smaller ones have seen better days as well, but might be able to get these a little easier. Where have (has anyone) people go replacement ones from? or it is worth just...	shack	5	2291	Feb 10, 2012 by shack
	Quick MoT test question .... (Preview) Hello all, My newly acquired TTR will be going in for an MoT test next week, but I have one question. The original number plate assembly (regular size plate, reflecter, number plate light) has been replaced by a slightly smaller number plate, with no number plate light and no reflector (it has a red...	fatboy686	4	754	Feb 9, 2012 by fatboy686
	another one for TTR fan (Preview) mate any chance of posting a pic of the difference between your great looking footpegs and the standard ones. how much would these be shipped to Australia too mate? cheers!	davecambo	2	649	Feb 9, 2012 by Cubber
	FMF powercore 4 exhaust (Preview) Hello i purchased a fmf silencer for my bike and fitted it on, there dosent seem to be an increase in power, (just louder) was just wondering if anyone has fitted this exhaust and had to re jet it? Also if the exhaust will do any damage to the engine will different back pressure? (was thinking of putting t...	dan-reeves	5	2161	Feb 9, 2012 by davecambo
	Won't start after a hose down.. (Preview) Hi folks. Hosed down after a ride a few weeks ago, put the bike away. Today, no start on the button or kick. Turn over but no fire. I have power, checked the spark, checked fuel is flowing, drained fuel from carb, checked airbox is dry. Removed tank to get at all the electrical connections. Gave them a...	DC	14	1933	Feb 9, 2012 by TTRfan
	Bashplate Dims Required Please (Preview) Hi I'm in need of a bashplate and have access to some good fabrication facilities at work. Would any of you be so kind as to take a photo / produce a quick sketch with the key dimensions so I can get one fabricated. I could of course take some measurements myself but thought it better to use a trusted design :...	tonyh210367	0	726	Feb 6, 2012 by tonyh210367
	take a look at this please (Preview) hi there again. I have pulled my sparkplug and taken a picture of it. what do you think? it has both black and white parts. just trying to work out if its rich or lean. And while i have you looking, this rubber thing was sitting on top of the engine next to where the spark plug goes. what the hell is it and where...	davecambo	3	863	Feb 5, 2012 by davecambo
	break in oil (Preview) hey guys, i got to 200km and changed the oil on my new 2011 TTR. it was very black. i then put spare full synthetic oil i use in my ducati 1100 in the TTR, but have since remembered that this may not be recommended for a new bike like my TTR as it hasnt finished breaking in. I read this is because of glazing in the...	davecambo	2	1312	Feb 4, 2012 by davecambo
	clutch houesing has scrape marks on outer edge (Preview) hi any feed back would great i have a ttr 250 06 it has been riden hard 3 day bike rides through country sides still running fine ..very reliable great bike but i have found scrape marks on the clutch housing also it make a metal spinnig noies under duress and also when changeing gear any imfo would be gr...	barto	2	1181	Feb 4, 2012 by barto
	will adding a 47 tooth rear sprocket need bigger chain (Preview) i am running 13 front and tomorrow changing to a 47 rear sprocket instead of the 44. will i need new chain?	davecambo	3	1529	Feb 3, 2012 by davecambo
	staintune (Preview) after being paid a little more than usual, i now have a budget for a better or more expensive exhaust. staintunes are very good australian built exhausts and for 640 Australian dollars it could be the one i buy. just wondering if any aussies have put one on a blue ttr, even better a late model blue one like...	davecambo	3	1187	Feb 3, 2012 by davecambo
	can i use castrol? (Preview) can i use castrol race edge oil that i have heaps of at home, or do i have to use yamalube?	davecambo	1	1669	Feb 2, 2012 by Cubber
	Clutch and Throttle Cables - Any other models fit? (Preview) Hi All Just a general query to see if anyones aware of any other throttle or clutch cables that fit the TTR. Cheers, Tony	tonyh210367	1	713	Feb 1, 2012 by Cubber
	is a 2006 the same as a 2011 (Preview) i think this has been asked already but are there any differences between the 2006 TTR and the 2011 TTR exhaust wise. I have made up my mind and am buying a FMF exhaust, but the company only lists them for models up to 2006. I think this is due to Aus and NZ being the only countries to keep producing them? Obvi...	davecambo	2	763	Jan 31, 2012 by davecambo
	fmf slip on ONLY (Preview) just got off the phone with a stockist for fmf here in Australia who said he wasnt sure if adding a fmf powercore 4 slip on would give any improvement other than weight saving. can anyone on this forum that has replaced the muffler only, ie - kept the original header pipe, tell me if there was increase in p...	davecambo	2	965	Jan 31, 2012 by davecambo
	Yoshimura RS 3 exhaust on (Preview) Has anybody seen a yoshimura RS 3 full system exhaust fitted on a ttr before, if any body has an experience with it or if there is a full system that is better for the ttr, I don't mind if it was little bit loud. -- Edited by Abbas on Saturday 7th of January 2012 01:30:43 PM	Abbas	3	2219	Jan 31, 2012 by davecambo
	Pics to show location of rear footpeg mounts on a Raid (Preview) The pics are for Valkman who is looking to improve the rear footpegs on his OE. I can't find a decent pic showing the pegs fitted. Can a Raid owner help out please?	TTRfan	3	701	Jan 30, 2012 by spud351
	lexx exhaust (Preview) came accross the brand Lexx exhausts. they are quite cheap here in australia. 270 dollars. Just wondering how they would compare to fmf or similar.	davecambo	5	1666	Jan 30, 2012 by Metalbender
	so i messed with my mixture and now it goes like a pig. (Preview) as the title suggests, i messed with my mixture on the carb and now it goes a bit like a pig. I tired the whole thing of warming it up, then adjusting the idle speed to a little higher, then turning the mixture to the right until it almost conks out, then turning it to the left till it sounds better, but while r...	davecambo	10	6802	Jan 31, 2012 by fwtian
	Can can (closed) (Preview) Why run around with a bare rear suspension reservoir? If you loosen the hose clips and free the reservoir you CAN wrap a cover round it. You CAN also drink the contents before cutting the CAN as required. Cheers ...... Martyn	Cubber	8	1223	Jan 28, 2012 by Cubber
	why remove any of the top of the snorkel??? (Preview) just wondering if someone could explain why someone would remove the whole snorkel, when technically wouldnt removing ONLY the bottom half that isnt visible from the outside of the air box give more breathability, whilst keeping the curve on the outside to deter water? im thinking that having only...	davecambo	3	1137	Jan 28, 2012 by dfaz
	Part number (Preview) Can anyone provide me with a part number for a few decent options for air filters please.	davecambo	1	691	Jan 26, 2012 by truslack
	1996 white ttr (Preview) Hi all, i have a white ttr and and i will need to rebuild the engine. I have two crankcases left and right that i bought from Brian sometime ago as the spring return post broke on mine and my question is do i need anything special in the way of tools to remove the crankshaft from mine to refit to the new crankc...	jasparach	6	1494	Jan 26, 2012 by jasparach
	what to add to new bike (Preview) gday guys, just thought i would ask people what options i have for adding a better exhaust system to the TTR250. I have a 2011 model, and noticed that there are lots of FMF exhausts on ebay, but they all say they fit models up to 2006. will these fit the 2011 model also? If so, what can i expect from an exhaust...	davecambo	2	1023	Jan 26, 2012 by TTRfan
	Question about bike (Preview) Hello again, ok i have owned my ttr250 for 3 1/2 years and i just want to know something, When i blip the throttle really fast when idling it bogs, Is this a normal occurance? or it is the jetting, It has a standard 147 main jet (aussie) and 52.5 pilot jet, and a Fmf powercore 4 exhaust, it seems to be running r...	yamahaTT250R	3	872	Jan 26, 2012 by Aidan
	Alternative Bash plate (Preview) Now I have seen a rather fancy all singing and dancing Bash plate/ sump guard on recent trip to TTR Towers, but wondered if any other guards fit (have seen an XT500 guard going cheap) has anyone had any joy with other OEM gaurds fitting, or being easily adapted? Piccies always a bonus.	shack	1	1158	Jan 26, 2012 by Cubber
«First < 1 … 59 60 61 62 63 … 65 > Last» \| Page of 65 sorted by