Recently I've had a couple of starting problems, the first I have now fixed which was a faulty starter solenoid. My second starting fault is when starting from cold it fires up straight away as usual but pops and stalls. Today I began removal of the carb to give it a clean as I was assuming a dirty jet w...
Its in a tiny town named Mooball. NSW. AUsrralia. Only had two minits to take a photo. It is a ride able bike. Has a japanese 4 cyclinder car engine and front rear discs from a car. It also has training wheels fitted as i guess it would take a 300 kg man to lean it into corners. will try and get more pics of th...
Found these in the drawer and ive no use for them now ,all to fit ttr 250 Four new filtrex oil filters Front and rear wheel bearings and seals for blue tank (full set quality koyo and fag bearings and double lip seals) New single linkage bearing and seal (not sure which part of linkage 20x27x5 needle) Used...
G'day Folks, Craig Here. I'm a vintage mx enthusiast keen to get hold of one of these babies. Just love my four strokes...especially the slow revving ones.
Hey Guys, Just brought myself a ttr for my first bike and can say i love it! Was looking for something low maintenance and reliable, so couldn't go past the ttr. Gets me out bush and back every time hassle free ! Double thumbs up
This is an extract from my project bike thread so it may read a little odd in places. I thought it might be useful to start a new thread for this job as the original post will get lost in time. The first bolt attaching the linkage (or relay) arm to the frame is usually well stuck in. The main bolt's LH head (on o...
Hey Folks I don't have a TTR yet but am not too far off and would love some tips on what model to look for or avoid. I'll probably be looking at 2006 to 2010. Is there much difference between the models? Thanks in advance for your help. Craig
Cripes - what a job that turned out to be Both bulbs on the number plate unit had blown. If one was still working I wouldn't have bothered doing the job. As is common on older TTRs that have been subject to mud etc, both nuts were fully seized on and weren't going to budge without special treatment I skim...
My OE runs fine in good weather condition but when riding in rain my throttle feels very sticky and when I let off the throttle grip, it jammed at about 1/4 carburetor opening thus I had to force it shut to an idle opening. However when I turned off the engine and twist the throttle open and close, it feels n...
Picked this up for the-over-half's newly acquired TTR, only to find - after a real good clean - that it already had a lowering link fitted....drrrrr! A few marks from being in use but bearings and grease nipple both A1 £65 + p&p
My tank has abit of play when straped to the frame. About half an inch or abit less. I would have thought its suppose to hold the tank more securely. The round rubber thats on the frame is in good nick. i can lift the rear of the tank when the straps on. Its as if the straps a tiny bit to long. Anyone else got move...
Hello everyone. Question is what are the dimension`s of starter`s o ring???? Mine is leaking oil a lot from there and need to replace it. Problem is that i live in Finland and the bike is in Greece.. :) so i can`t measure it. I`m leaving on wednesday to Greece and going to fix my Raid again. So if anyone kn...
I am sorry to report that Andy "Fixer" Lander-Stow is suffering poor health and has given up trail riding and sold his TTR250. He has also closed his TTR250 shop and passed the parts over to me. Motad silencers here Rear shock top bearing kits here 2-bolt chain guide protector blocks here An...
See here I recently bought a job lot of new spares from an ex-TTR owner who is sadly having to give up trail riding for health reasons It was quite an unusual assortment of parts. Just go to the web page and scroll down through and you will see what I mean! Brian
Wow - what a difference! I looked at the new national TRF (Trail Riders Fellowship) web pages here for the first time in ages and what a nice surprise. They are a vast improvement over the old version. Well done to the TRF webmeister Two nice TTRs on one of the photos here Brian
So, ive picked up a blown up 2001 TTR250 from forum member scott and its a perfect candidate for a rebuild and to replace my troublesome 94 model. This wont be a quick build up as the usual family / work and financial pressures get in the way, more so it will be a bit spasmodic. Plans at this stage include: re...
Full set of Original Yamaha Indicators. From a low mileage 2004 TTR in really good condition. Rears has the brackets on them. Someone make me an offer for them all!!
Full set of working indicators for your Raid or Open Enduro. £10 a corner or £35 for the full set. Email me here if you want to buy. More used TTR parts here but if you don't see what you want please ask. Brian
Any imfo would be great. WR tail pipe has to be lighter. Maybe less restrication. As soon as i get it i will post the weight of it. local muffler shop will modifiy mounts or anything needed.
Not sure what they are called, the rubber bushes that you clip the plastic side panels into are falling to bits on my OE, had a look on Brian's site but didn't see them. One of the panels is moving about quite a bit so have used some tape as a bodge, don't want the clip to break off. Any help would be appreciate...
Hello all, just looking to do a bit more dress-up for the bike now that she is running like a dream. Does anyone know of a source that supplies billet timing plugs preferably the color blue anodized. I haven't thought of measuring them myself, is there a changeover between some of the YZ__F models?
will try and get more pics of th...
