Hi, i need help with my 1996 ttr oe. i originally wanted to install led indicators so i did and replaced the relay as well. the indicators were crap and i just bought some tungsten ones but when i replaced the relay i pulled the pins from the plug on the adapter to the old relay and now i don't know the origina...
I am curently restoring the pretty metallic blue tanked version of the 4RR2 model Open Enduro and had a problem tracing a headlight fault.I was surprised to find a relay under the tank which I hadn't come across before. Looking at the parts manual, this relay was only fitted to the 4RR2 and 4WA1 (Raid) m...
Hey, this is the bike I've been restoring coming back together. I just finished rebuilding the engine and put everything back on the bike. The first firing attempt will be happening days from now. Very excited. Anyway, the crankcase has new bearings and seals, I honed the cylinder and put in a fresh p...
The speedo drive on the TTR can easily be stripped out and rebuilt.The photo below shows the parts involved and I am pretty sure the drive can't be dismantled further. If anyone else knows different please say! I have included in the photo a brand new drive for interest.Fit the parts in order starting...
I have a 2000 TTR250 that I just bought. Started fine several times before I bought it. Got it home an hour later and it wouldnt start. Really sluggish like battery dying. Had new battery installed. Worked fine rest of day and started once this morning and wouldnt start 15 minutes later. Same problem....
hi everyone, A couple months ago I was changing the spark plug on the bike and decided to do a compression test only to find that The gauge read only 60 PSI. I'm pretty sure it should be way higher than that. The bike still runs extremely strong and it doesn't feel like there's any power loss could this jus...
Hi all,I have a problem with the charging system on my newly acquired TTR250 1995.Symptoms are battery drain of 0.2V/hour, so it’s flat the next day. Also no charging when I rev the bike quite high(I don’t have an inductive tachometer) – the voltage across the battery stays at its initial charge of ap...
Hello everyone,I have just about wrapped up overhauling my engine. My final inner engine task is the clutch plates I have just now installed.Here's my issue-The last time I played with one of these clutches a few years ago, I busted my spare. I put an improper torque wrench to the clutch spring screws...
Hi everyone. I just recently bought a 1999 Ttr250 As my first bike. I has been great so far. I Know I'll be asking a lot of questions and I'll try to answer some as well
Hi All Still have the TTR wheels left, sorry everyone else but Australia only Front and Rear wheels, axles, Discs, you will most likely need new bearings for both, they are a bit noisy wheels spin nicely with very little run-out, postage at your expense, these wheels will fit all models of TTR250, pack...
Hi all, Bit of an ask but I am looking for an analogue speedo mount, plus a speedo and the warning lights, mine only came with the warning light ty-wrapped to the bars (after an altercation with a tree...) which is rather worse for wear but works. If anyone can help with any of the above it would be greatl...
Just wondering if theres a good how-to for installing front brake pads I used this - http://www.ttr250.com/TTR_rear_discpads.htm for the rear ones and it was very easy but not sure how to do the front ones
In sunny weather (yes, we have had some in the UK!) it can be difficult to see if the neutral light is on so I have just changed the bulb for an LED one and it has made a huge difference! The TTR uses a capless bulb and it wasn't difficult to find an LED version: Before: After: Bright eh? Nice easy job Bria...
If your original unit is damaged or missing and you are fitting an after-market switch you may need some additional parts. When I was building my project bike, these are the additional parts I needed to properly fit the switch. It is more than likely that you will already have these on your TTR. Firs...
Hi the speedo stopped working so today had a look. . Spin cable at bottom and speedo needle moves . put a match in bottom pic up and it spun intermittently ie a couple of sparodic turns every turn of the wheel . Stripped and cleaned pic up and found the problem . The 3 tang washer had lost its flat sides ( see pi...
