Hi, new here, can anyone help? I've got a problem with my 2001 ttr250! I hadn't used it for nearly a year, but started & ran it regularly though..... I realised over the last few times that it ran perfectly on the choke but when I switched off the choke it had started searching for an idle, popping &...
Building a motorbike rack for my motorhome - pretty much last thing I need to do before going for a test trip of the van down to Devon to hopefully do some green laning and a bit of surfing.. Going to weld the 10mm steel plates to the sides of the tow bar: I've already cut the step down at each end so the triang...
Selling an Acerbis long distance tank originally from a Honda XR Capacity is around 22L Both fuel taps have recently been renewed. Comes with all pipes for fitment. Price includes for the Zen Overland fitting kit which will fit Blueys. Can remove if not required. This tank has small removable Acerbi...
Hello All. I'm new here and following instructions, so better introduce myself. I'm a owner of a TTR250 which I purchased (quite possibly while being blind folded) in the beginning of this summer with the intention of rekindling my youth (dream on sucker!) and enjoy being back out on the trails. The...
Hello everyone, and as the title says, i forgot to set my motor to TDC before i removed the top end for a re ring and cleaning. My question, what do i need to do in order to make sure i have no problems after reassembly? I know how to set the timing etc. but i am concerned that i forgot to do this before i disassem...
I have read loads about sprag and didnt want to hijack the one below. My bike makes a clunk its not very loud but its there so I did some reading on here and looked behing the cover near the starter. The idler gear is damaged but the starter should be okay. I have added a picture of gears but what do you people r...
https://www.ebay.co.uk/itm/Yamaha-TTR250-Open-Enduro-1998-Low-Mileage-Excellent-condition-for-age/323487519805?hash=item4b515bd43d:g:Kv4AAOSwA-Nbuh52:rk:1:pf:0-- Edited by ttr steve on Monday 15th of October 2018 10:39:10 PM
I've got for sale the swing arm bearing set I brought from totallyttrs that I never got round to using. They're still in the packet not been touched. £20 plus postage 🙂 Cheers Jordan
I have a 2002 TTR250. It has been maintained well throughout the last couple of months since I bought it. Last Saturday morning, I tried to start it up with the choke and it started right up. Couple minutes later, however, it died and wouldn't start up again. I decided that it might be the carb that need...
Hey peeps Anyone had the experience of the aluminium with o-ring blanking plug leaking? I think I put it in about a year ago. I guess I'll pull it out and clean it and maybe use some sealant as well this time? Cheers Leigh.
Having spent a fortune on parts after the Sprag being worn and other items it was good to get out around Pendle Hill for the first time I would have taken more photographs but phone battery died lol
Not sure if this should be in the ride report section rather than here as it was more a sportif-tour than overland expedition, but it's quieter here and hell, 1000 miles of desert riding in 11 days oughta qualify? 8 Brits, 2 Swiss and 3 Germans with a German support truck went for a play in the Algerian sah...
hey you all my starter worked and then it quit and it just clicks and if i hit it with something it will turn over a little bit and then start spamming out and it acts like its bad or the starter itself is locked up it only works if i hit it and my bike wouldnt even start when it was working i checked everything an...
Every day is a school day! Although it was possible to adjust the clutch on Steve's 350 build to get the pointer in the correct position (see here), the bolt did seem a long way in. Shoulda realised that the bolt was from a 6-plate clutch and Steve was upgrading to a 7-plate which, ideally, requires a long...
Google translator Once I came across a thread and advice that it is good to go in company, what to take with me, how to drive in the sand, in ruts, etc. Where can I find him? Thank you.
Maybe of use to someoneMotorcycle suppliershttps://totallyttrs.com/http://www.fowlers.co.uk/parts/from_fowlers_web.htmlhttp://www.cmsnl.com/http://www.ebay.co.uk/http://www.ebay.com/http://www.exhaustdirect.net/mac_exhaust.htmhttp://www.boats.net/parts/se...
I'm going to be selling my oil cooler off my ttr. Its all there as I've removed it from my bike before I sell the poor girl. I'll attach some pics at some point but I'll ask throw in the blanking bolt it requires and the banjo bolts to connect it up. Any questions just ping me a message 😊
picked up a 90ttr a few years back for $200, the bloke said he replaced tchain and could start since. A bit a basket case. Thanks to me stalking this forum, it's now a runner. How do I gain access to the service manual download? cheers
Is anyone aware of a simple speedometer option for the TTR? Really only wanting speed...analog would be fine in order to keep it simple (both to use and to install, as I'm not especially mechanically-talented!). Thanks!
Hi All, New to the forum.. hope you're all well. I recently picked up a 2006 TTR250. It was not running but I've managed to get her going. There's a strange problem that I can't work out. When I start it cold, with the choke on she runs quickly to high revs then settles down to lower RPM after a few seconds. ...
I had a conversation with a friends a couple of years ago, "Maybe I should be looking for a TTR250, or similar..." Phil said, "I've got one of those. You can have it. If you don't, I'm taking it to the tip." So a few days later I added an 02 TTR to my collection. Bit of a Yamaha tragic with a separate love for...
Hello all, my 1999 250 TTR Enduro is brilliant and love it only used to go to the shops on dry days.only 8800kms. Reading posts on this page it appears that to hear a clunk when the engine is turned of is a sign that a sprag clutch is on its way out. My bike starts and runs fine. Do I have a problem???? My only s...
When putting my bike back together I found my clamp on the air filter side of the carby wasn't clamping tight enough. To keep the original clamp I cut a cable tie (flat end ) so it was a neat fit around the tube then put the clamp back on over the cut down tie end Result was a good tight clamp again -- Edited...
Hi from Lancashire just got my ttr250 metal tank model and out for first time today, straight through MOT but have a few problems I hope you lot can sort
Sorry to post an advert on here, but it has taken me ages to get brake discs sorted out! I got fed up with a bad supply chain from other suppliers and went in search of brake disc manufactures. Dealing with EBC was impossible and then one of my customers (thanks whoever it was!) told me about ABE in London. I...
