Hello, I’m looking for a carb for my 2004 TTR250. My first choice is the OEM Teikei Y30P but I’m open to another model that fits. I‘m in Sacramento, Ca, USA -- Edited by Riding Rookie on Sunday 9th of November 2025 05:13:44 PM
Had the day off today did a ride upto gingers creek on the Oxley highway for lunch of course went the dirt way a total of 207km . Pretty rough and a bit hot but a lot of fun .
I'm going to replace the main switch block the one with indicators, high low beam and horn are there any aftermarket ones that will have no problem with the white plug already as part of the wiring loom? Also I'm looking for recommendations for any with good and easy to cancel indicators because I am usi...
I have found an oil leak coming from the left side of the bolt and copper washer from the top oil delivery pipe I've looked in the service manual and it says: oil delivery pipe union bolt M10 x2 20Nm oil delivery pipe union bolt M8 x1 18Nm but my bolts are 14mm x1 top bolt and 12mm x2 lower bolts, should I stil...
Just joined. Have a 2007 which I’ve just got running after sitting for 5 years and a carb refurb. Had an 94 OE about 20 years which I used green lanes in Scotland and Yorkshire. Looking to replace tyres for a mixture of road and trail if any one has a recommendation? Thanks Paul
Hi im in Australia and needs full set of plastics for 1998 open enduro white has anyone remanufacturged these ? Is there any interest in getting some scanned and printed at least?
Hi all,I bought the bike with 6000 kms on it.It was running perfectly,no coughing spluttering,no flat spots,ect...I was quite suprised at the power it put out(having just sold a Wr450F 2016 model),and thought it was quite grunty/fast compared to a WR250R I had many years ago. When I bought the bike...
I just got a compression tester and my bike has a reading of 200 psi with the throttle open and a cold test it feels a bit sluggish so I'm looking into checking valve clearances, from memory the manual says 175 psi is standard so I'm wondering how is mine 200 psi. My tester has schrader valves in the hose at t...
Hi all,just wondering if anyone has had there TTR250 at 6000 kms or higher,and have performed a valve clearance check,and found their clearances have not needed adjusting?Or if your valve clearanes were out,what were the signs that made you inspect them? If your valves are not in tolerance,will it...
Hello all, hoping to get some info from the experts on the forum So, I purchased a 1994 TTR250 Raid around 3 weeks ago, rode it home on the day I bought it (around 85 miles) and the speedo and odometer was working perfectly, it was placed in my garage so I could check it over in my own time, I removed the batter...
Wanted Chris from Grunt motorcycle training Australia. Are you on here Chris? no response to any emails or whatsapp, thought I would try here before I cancel the whole order and refund you. Steve
Hi all, introduced myself a few weeks ago, as yet to buy my first TTR250. Since then I got myself a '93 OE. No pictures yet, but, you know what they look like right? Seems fairly stock apart from the Red bark-buster type grip guards. The bike seems in pretty good order, with the following list to fettle (...
Hi all, just sold my WR450 and bought a Ttr250.What an amazing little bike.Feels so light and nimble.Had a Wr250r many years ago, and this Ttr feels a lot more grunty and faster than that,but maybe my memory is wrong.I have the standard 14/44 gearing, and think I might put 13 sprocket to see if that helps...
I have a problem with Spark. (It only sparks for less than a second ) I have removed the spark plug and left the spark plug lead on and press start, the motor turns over however the spark only last a second then nothing as the motor cranks over. If I try again nothing. However if I let it sit for ten minutes...
Hello and thanks for letting me join, I'm new to the forum and to TTR250 ownership, I recently purchased a 1993/94 TTR250 Raid which is generally in good condition for it's age, looking forward to having a bit of off road fun on it very soon, I'm located in North Hertfordshire.
Hello, I'm a new owner of a 1993/94 TTR250 Raid, I've decided to change the front fork oil and noticed on stripping the fork legs down that there is no internal damper rod connected to the fork cap, is this normal ? Been looking for a workshop manual that covers this bike but they seem to be hard to find ?
Just a brief reminder about this great bit of kit.I was experiencing charging problems on my latest TTR refurb project. Somehow, I managed to kill my digital multimeter so I was unable to do the stator resistance and charging tests shown in the workshop manual.After a flash of inspiration (don't oft...
Been lurking for a while, was undecided which first dually to get. I considered XT350's, TT350's, XL400R, XL250R, WR250, In the end though, I think I will need an elec start, plus I'm impressed with the community you all have over here, and support from Totally TTR. As for the WR - a bit heavier, bit mo...
Ok, bit of a back story but I bought my bike from a friend who drove to Devon to buy it from a guy who used this site alot. Sadly I believe the guy was very poorly ( in fact I don't want to use the word but I believe he had terminal cancer.) So my mate had a great day with him pootling down some green lanes and brough...
Hi There are a lot of how to fix enquiries on the Forum, which is great, I think a few more pics and stories of TTRs out and about around the world would be great, seeing TTRs in their natural habitat is always good .
HELLO ALL! Found you via Google. Im 67 and riding since about 10 years old. Started on those Honda 50 and 70's we all love. Got a used 2003 TTR250 for $1400usd. When I went to get it he agreed it had a idle problem. Would stall if you didnt hold a little gas on. But other then that rode and ran great and shifte...
Hey all, just getting back into riding after far too long away. I want/ need to do some jobs on the old girl but would like a paper manual.... Ive got the computer version off Brian but find it a pain. My question is.... was the 1998 a weird year or something as all the manuals ( Hayes and clymer) don't come up...
Well after some serious health issues last year & an operation to correct it, plus was not allowed to lift for 3 months. I rode the WRR 4 months ago in pain from my left hand ( Viking hand) could not pull the clutch in & didn't use the clutch most of the ride. Pulled my finger out & had another ope...
Is there a replacement cable or one off another model that will fit ? I can find new ones but they say I'll need to wait 14 days ,and I need one for the weekend as I'm doing a long distance trail on Sunday.
So I've just changed a leaking fork seal and refreshed with new oil. Now we nipped up the 14mm base valve nut at the bottom of the forks with the idea of fully tightening when the fork is back on the bike. We can't get the nut to tighten and it sounds like somethings spinning inside to fork. So a bit of digging...
