Hi all. I just haven't used my ttr any where as much as I thought I would (less than 300 miles !) So it may be time to sell up. I'm just gaging interest at the moment. It runs and rides and has had a new cam chain + magnetic sump plug and an aftermarket digital speedo fitted. I have sourced and fitted an original...
A friend has just returned from the Philippines- where he bought me a few sets of these. Steve (owner of this site) kindly offered to try to source some, as it took me over 1 year to get these. they DO FIT the TTR250 BLUEY (obviously they come in blue!!) ...am I just "odd" believing they finish off a TTR?!!...
Hi guys, Just to be clear: all questions I'm asking not usually are just from one motorbike. As I'm helping my friend at his garage, first TTr was the one I wanted to keep; second belonged to a customer, than then brought a third one, so yes, they are three TTR's I've been/I'm asking about. While checking...
I can hardly believe that it has been over 7 months since a have been green laning on my TTR! I met up with a couple of mates this afternoon but it was more of a social and catch up than a serious trail ride - which was absolutely fine by me after such a long lay off. Nice to have the heated grips on the chilly road...
All the bikes I have owned that had bad piston rings had oil in the exhaust or combustion chamber or showed on the spark plug and the bike I currently have shows none of these issues. However I have little to no compression stroke when turning the engine over from the crank with the socket I have no resist...
Hi there everyone ! my rear suspension is way to hard even after adjusting the dampening to soft and the adjuster on the bottom of the shocker. I would like to back off the spring tension by undoing the two adjusting nuts ( I have the tool for this ) but getting to it looks a tad difficult, can you simply remo...
The guy who owned this ttr 250 before me apparently did not know that the float pin only comes out one way and broke both of the float shafts right at the hole. He put JB Weld on it but as soon as I put gas in the bike they softened up and fell off. What's a good alternative for repair? I tried to solder them And...
Has anybody upgraded the springs in the standard 43mm forks, I tried to get some progressive springs from Hagon shocks but they don't make any. I was just wondering if anybody had done anything similar? Cheers Andy
Hi guys,New to the forum,have a 2000 ttr 250. long storey due to theft recovery I have no more motor so looking to buy something complete. I'm in Canada so shipping would be a must. Let me know what you have. 1999-2006 should work. I ll rebuild it if I have too just trying to get her ready for this spring. Tha...
Hi There, I brought an oe a few weekends ago and it was great ran lovely and was a great introduction to dirt bikes. Unfortunetly the second time out with d.lee22 whilst riding back I heard a loud snap. Once the bike was recovered, I removed the rocker cover only to find the cam chain had jumped off the out...
I thought I would upload this for people wanting to understand the TTR250 carb. Hope you enjoy it.1994 standard TeikeiY30P 2004 standard TeikeiY30PTools needed for the job .....
Hi, brand new rider from the middle of the US. I just bought a 2004 TTR250 last week, and have been reading all I can about it. I'm a new rider, with just a few hours of dirt bike experience from last summer. My 16 year old son and I hope to have a lot of fun with the bike this year. I look forward to digesting...
hello all, I am looking for larger foot pegs then what the factory offers. but in Canada its hard to find listings for the ttr250 for pegs. what other bikes use the same pegs as the 2006 ttr250?????
my son runs a ktm with extra thick innertubes bit of a pain getting tube air valve in to inside rim has any one tried these tyre air valve pullers on ebay £6.99
I have owned this bike for four years and used it regularly. I have enjoyed riding it but have been offered a much newer one, hence the sale. It has new piston rings and doesn't burn oil. It was MOT'd in the Autumn. It has a Vector electronic speedometer. I have the old speedo but I do not know the milea...
I have a complete and unmolested airbox, including the filter cage and full snorkel for sale. Came with loads of bits when i bought my TTR and thought it may be useful to keep should i ever want to try the snorkel mods etc.. But, im far too happy with my TTRs performance so instead of it languishing in my...
I have just put an advert on eBay for a Honda CB250RS kickstart lever but am mentioning it here as I got it off a TTR250 that I broke for spares so I know it will fit The photo below shows the lever fitted to my TTR250. It's a very tight fit and touches the clutch case and frame - just - so be aware that it isn't a p...
Here's my first ttr "ground-up" (last resto was a ccm 644 - lovely bike but riding it just didn't inspire me like the ttr does) As bought: As you can see, she's been leaning against a wall for a while Time for the hot air gun and the massaging hands! Powder coater's tomorrow... -- Edited by mossproof on W...
Hi All After long period without 2wheels I bought TTR250. As I knew from Azerbaijan Yamaha dealer there are just 2 TTR250 in my country)) First of all I changed vinil and removed rear turn lights.
Off to meet my mate Boz from this here forum tomorrow. I am looking to put on a totallyttrs weekender in September (when the kids have gone back to school) and Boz has offered his services on plotting 2 days riding Mid country. We will be looking to do some really nice green roads and have a nice lunch stop...
They are quite a bit taller than TTR forks as you can see from the photos. Also, the axle clamp and brake caliper are quite different. The only bikes I have ever broken for spares have been TTRs so these came off one a few years ago so I know they will fit but I wonder why the owner fitted them and what bike the...
