A forum for owners of Yamaha TTR250 trail and enduro bikes!

sammyttr · sammyttr

I haven't started the ttr up in over 2 months, the carb is empty of fuel, turned it over a couple of times with battery being flat, will the bike be alright being stored up this long sat in a garage as well and regularly sprayed with wd40

suzbandit987 · suzbandit987

in the FAQ Section, it says this about fitting a diff rear fender:After-market plastics. You can't get after market plastic for the TTR except an MX style rear fender. You can put any aftermarket YZ/WR front fender on it though - just cut off about an inch in the back. These on-line sites are probably th...

davecambo · davecambo

im mainly doing trail riding now so i was wondering if you need to keep the batttery. it would save some weight if it wasnt there, and kick starting a ttr is easy. would it be worth removing it, if so what else could i remove from the electric start system to keep the weight down.

barra8 · barra8

Hello readers,thanks for taking the time to listen. I am stuck with a problem that nobody seems to be able to confirm for sure (not even any yamaha dealers)

. As i have a 1996 ttr 250 open enduro part (4GY). I am looking to buy a complete gasket set for it. Just wondering what other year parts w...

Gmon82 · Gmon82

Hey all, I have a sneaky feeling from reading througth the forums that I have totally worn out the clutch on the bike but wanted to get some more opinions before I take it to my mechanic. When I go to one here in Cambodia I will be charged extra for being a foreigner and not knowing exactly what is wrong (plu...

TTRfan · TTRfan

Just started to refurbish a blue TTR and stripped out the swing arm this morning as there was quite a bit of play. Once out it was fairly obvious why! Experienced owners will know to keep an eye on the chain slider and replace it before the front bottom section by the sprocket wears through but I have poste...

barra8 · barra8

Hey guys, been stalking these forums for a while now and think that there is so much usefull info so thanks. I am stuck with a problem the problem being that i want to buy a wizeco piston and ring kit off ebay and wondering whether it would fit my bike. eg. http://www.ebay.com.au/itm/Wiseco-Piston-K...

wizz · wizz

I have a 94 o/e, standard.I have a new new pipe to fit (thanks ttrfan) I want a new air filter (any suggestions?) and jets?,I am taking it to a local dyno shop ,should I buy jets first or wait for his advice? I have read loads of posts but are still clueless. Mark.

barra8 · barra8

Hey guys,i'm new here as you might notice so i hope i aint asking already asked questions. I have a open enduro-white ttr250. My problem is that no matter how hard i try i cannot find any info on rebuilding the top end. Have found a vague description on some of the work but nothing solid. It has been 5 long ho...

tracker · tracker

The last few weeks i have been riding with guys who all have 250cc KTM's (four & two stroke) .On every ride that we have had at least one KTM have needed some sort of attention (not trail damaged), while my well used TTR just keeps going.These guys are good riders (fastish) but the time waiting for th...

pedrosan · pedrosan

Hi guys, anyone able to recommend a competent quick good value garage near (within an hour or so) Keighley, West Yorkshire? I need a quote for valve clearances, engine service and general spiffing up mechanically. I'm trying to work out what to do while I still struggle with the jammed in sump plug. I'...

yamahaTT250R · yamahaTT250R

hey guys, i have recentlytook off the head and put a new gasket plus fitted new rings onto the piston and cleaned the valves, reassembled them then i turned on the motor and it turns but this strange ticking noise seems to have shown up im not sure it was there before but hany ideas on what is could be? ill po...

nwrider · nwrider

i am thinkin about ordering the qr exhaust, at the same time should i order new jets, and which ones should i get, is anyone else running this exhaust

TTRfan · TTRfan

I am guilty (and I am not alone in this!) of forgetting to cancel my indicators on trail rides and this causes concern amongst following riders for some reason Anyways up, I bought one of those 12v buzzers from Maplins about 18 months ago and have only just got around to fitting it this morning. With...

raptor57 · raptor57

my bike is old thoughly trashed heaps of ks still hit that button its off but sadly now it throws into neutral would it be selector ? how do i rectify this prob thanks

wizz · wizz

Hi can anyone tell me where to get a front caliper repair kit from.I have a 94 o/e many thanks Mark.

rvyhnr · rvyhnr

I have rebuilt linkage and rear absorber bearings in my 96 OE with all balls linkage kit and after putting it all together I have found that there is still a significant swingarm vertical play. I have realized that collars, that come with all balls kit (marked 27, 28, 29 on swingarm diagram from this si...

truslack · truslack

Hey, I'm struggling to jet my 1995 250 Raid. It has an FMF powercore 4 exhaust, and has had the top of the snorkel cut off. Can anyone advise on a good pair of jets for this setup?

Aidan · Aidan

Well I thought my bike was running rich as the spark plug has a sooty black appearance. ( not shinny black) However I read that if ur exhaust makes a popping sound it's lean.. My exhaust makes this on deseleration. ( i always thought this was maybe a bit of extra fuel burning). Any ideas?? The exhaust is an...

SteveGT · SteveGT

I have just re-assemblyed my TTR raid, after replacing the piston rings. When replacing the cam shafts, as soon as I tighten up the bolts the cam shafts become too tight to turn by hand. Even if I just do the bolts up hand tight they are really stiff. Is this normal? I have completely re-assembled the eng...

TDVT · TDVT

Hi there, Just got my bike registered & running well enough to start taking a few shakedown runs on the roads around town. Still more lighting & things to add to before it's inspectable & 100% street legal (USA). Tonight on the pavement, probably cuising in 6th, I noticed that the bars see...

swygert27 · swygert27

hi im new to the form just have some ? i have a 2000 ttr250 that was runnung great and now nothing so i pulled the carb cleaned everything put new gas pulled plug and its the wrong plug guy before me stuffed a 12mm plug in it insted or the 10mm so im stuck no hely coll will fix that so i checked fire and have good fi...

Nomada_Firefox · Nomada_Firefox

Hi, I´m from spain and I have a TTR250 from 2005. I have a problem, the dirt enter into the case saver and the pinion, I would like know if anybody have made any good solution. Thanks. Regards.

Aidan · Aidan

im currently running 14/52 sprocket set and was wondering which way to go on the rear or front sprocket to get a bit more acceleration. not so worried about top speed as on the trails id be lucky to get abouve 70km (most of the time alot lower ). thanks

colin13846 · colin13846

Anyone seen these in the flesh or actually have them fitted? http://www.demonmx.co.uk/contents/en-uk/d281.html

BingleBerries · BingleBerries

Gday Folks . Soaked & cleaned out the carby recently. All good but now when i ride up & over a certain incline (about 30 degrees) the bike starts "choking". Any suggestions really appreciated (even fat jokes accepted ha ha)

Jell · Jell

Hi everyone...new to TTR forum, go easy on me! :) Riding the TTR250 the other day I was going full throttle then it died and sputtered to a stop. I noticed right away the battery was smoking and was EXTREMELY hot to the touch. I got away from it to give it time to cool down...acid explosions are not fun. 2...

davecampbell · davecampbell

My 05 ttr 250 makes an awful clunking noise when it cranks and often repeats it when I shut it off. Anyone have this happen before that can tell me what to replace?

JuJu · JuJu

I have just started to run 95RON as apposed to 91RON Unleaded in my 97OE, the bike certainly runs better and cleaner i.e. no soot, but has been difficult to start electrically when cold. I don't have a hope in hell of kick starting it. Could this be the fuel or has something else eventuated?

Gcorner · Gcorner

Stopped on a ride today and noticed there was no rear chain block/guide/stay fingy. Bolts up at the rear of the swingarm. Am I tempting death by running without it, does anyone have one in Orstraya mate. There is one in the USA on Ebay for around $37Au delivered but prefer to keep things local, if anyone...

Topic		Started By	Replies	Views	Last Post
	Recommensing (Preview) I haven't started the ttr up in over 2 months, the carb is empty of fuel, turned it over a couple of times with battery being flat, will the bike be alright being stored up this long sat in a garage as well and regularly sprayed with wd40	sammyttr	2	825	Jul 29, 2012 by sammyttr
	TTR 250 Rear Fender (Preview) in the FAQ Section, it says this about fitting a diff rear fender:After-market plastics. You can't get after market plastic for the TTR except an MX style rear fender. You can put any aftermarket YZ/WR front fender on it though - just cut off about an inch in the back. These on-line sites are probably th...	suzbandit987	2	4025	Jul 28, 2012 by barra8
	do you need a battery? (Preview) im mainly doing trail riding now so i was wondering if you need to keep the batttery. it would save some weight if it wasnt there, and kick starting a ttr is easy. would it be worth removing it, if so what else could i remove from the electric start system to keep the weight down.	davecambo	8	2934	Jul 26, 2012 by barra8
	1996 TTR250 Parts interchangable??? (Preview) Hello readers,thanks for taking the time to listen. I am stuck with a problem that nobody seems to be able to confirm for sure (not even any yamaha dealers) . As i have a 1996 ttr 250 open enduro part (4GY). I am looking to buy a complete gasket set for it. Just wondering what other year parts w...	barra8	5	2722	Jul 24, 2012 by TTRfan
	Clutch question - is mine worn out? (Preview) Hey all, I have a sneaky feeling from reading througth the forums that I have totally worn out the clutch on the bike but wanted to get some more opinions before I take it to my mechanic. When I go to one here in Cambodia I will be charged extra for being a foreigner and not knowing exactly what is wrong (plu...	Gmon82	4	3444	Jul 20, 2012 by Gmon82
	Check your chain slider! (Preview) Just started to refurbish a blue TTR and stripped out the swing arm this morning as there was quite a bit of play. Once out it was fairly obvious why! Experienced owners will know to keep an eye on the chain slider and replace it before the front bottom section by the sprocket wears through but I have poste...	TTRfan	1	1342	Jul 18, 2012 by Cubber
	TTR250 1996 Piston & Ring kit (Preview) Hey guys, been stalking these forums for a while now and think that there is so much usefull info so thanks. I am stuck with a problem the problem being that i want to buy a wizeco piston and ring kit off ebay and wondering whether it would fit my bike. eg. http://www.ebay.com.au/itm/Wiseco-Piston-K...	barra8	2	1101	Jul 17, 2012 by barra8
	air filter,jet question (Preview) I have a 94 o/e, standard.I have a new new pipe to fit (thanks ttrfan) I want a new air filter (any suggestions?) and jets?,I am taking it to a local dyno shop ,should I buy jets first or wait for his advice? I have read loads of posts but are still clueless. Mark.	wizz	0	732	Jul 17, 2012 by wizz
	Top end rebuild (Preview) Hey guys,i'm new here as you might notice so i hope i aint asking already asked questions. I have a open enduro-white ttr250. My problem is that no matter how hard i try i cannot find any info on rebuilding the top end. Have found a vague description on some of the work but nothing solid. It has been 5 long ho...	barra8	5	2149	Jul 17, 2012 by barra8
	TTR vs KTM (Preview) The last few weeks i have been riding with guys who all have 250cc KTM's (four & two stroke) .On every ride that we have had at least one KTM have needed some sort of attention (not trail damaged), while my well used TTR just keeps going.These guys are good riders (fastish) but the time waiting for th...	tracker	2	799	Jul 16, 2012 by BM Steve
	Service and engine work; company recommendations near keighley (west yorkshire) (Preview) Hi guys, anyone able to recommend a competent quick good value garage near (within an hour or so) Keighley, West Yorkshire? I need a quote for valve clearances, engine service and general spiffing up mechanically. I'm trying to work out what to do while I still struggle with the jammed in sump plug. I'...	pedrosan	4	749	Jul 16, 2012 by pedrosan
	Strange ticking noise after I rebuilt top end (Preview) hey guys, i have recentlytook off the head and put a new gasket plus fitted new rings onto the piston and cleaned the valves, reassembled them then i turned on the motor and it turns but this strange ticking noise seems to have shown up im not sure it was there before but hany ideas on what is could be? ill po...	yamahaTT250R	9	7086	Jul 13, 2012 by TTRfan
	q4 exhaust jetting (Preview) i am thinkin about ordering the qr exhaust, at the same time should i order new jets, and which ones should i get, is anyone else running this exhaust	nwrider	3	1087	Jul 10, 2012 by truslack
	Installing an indicator buzzer (Preview) I am guilty (and I am not alone in this!) of forgetting to cancel my indicators on trail rides and this causes concern amongst following riders for some reason Anyways up, I bought one of those 12v buzzers from Maplins about 18 months ago and have only just got around to fitting it this morning. With...	TTRfan	5	6535	Jul 10, 2012 by truslack
	gears jumping out selector (Preview) my bike is old thoughly trashed heaps of ks still hit that button its off but sadly now it throws into neutral would it be selector ? how do i rectify this prob thanks	raptor57	2	725	Jul 8, 2012 by raptor57
	brake caliper repair kit?? (Preview) Hi can anyone tell me where to get a front caliper repair kit from.I have a 94 o/e many thanks Mark.	wizz	4	1096	Jul 1, 2012 by wizz
	Linkage rebuild problem (Preview) I have rebuilt linkage and rear absorber bearings in my 96 OE with all balls linkage kit and after putting it all together I have found that there is still a significant swingarm vertical play. I have realized that collars, that come with all balls kit (marked 27, 28, 29 on swingarm diagram from this si...	rvyhnr	6	1651	Jul 1, 2012 by rvyhnr
	Jetting help (Preview) Hey, I'm struggling to jet my 1995 250 Raid. It has an FMF powercore 4 exhaust, and has had the top of the snorkel cut off. Can anyone advise on a good pair of jets for this setup?	truslack	7	1732	Jun 28, 2012 by TTRfan
	Rich or lean (Preview) Well I thought my bike was running rich as the spark plug has a sooty black appearance. ( not shinny black) However I read that if ur exhaust makes a popping sound it's lean.. My exhaust makes this on deseleration. ( i always thought this was maybe a bit of extra fuel burning). Any ideas?? The exhaust is an...	Aidan	22	7799	Jun 26, 2012 by Cubber
	Stiff Cam Shafts (Preview) I have just re-assemblyed my TTR raid, after replacing the piston rings. When replacing the cam shafts, as soon as I tighten up the bolts the cam shafts become too tight to turn by hand. Even if I just do the bolts up hand tight they are really stiff. Is this normal? I have completely re-assembled the eng...	SteveGT	16	1912	Jun 25, 2012 by airmanbear
	Fork Alignment? (Preview) Hi there, Just got my bike registered & running well enough to start taking a few shakedown runs on the roads around town. Still more lighting & things to add to before it's inspectable & 100% street legal (USA). Tonight on the pavement, probably cuising in 6th, I noticed that the bars see...	TDVT	2	1022	Jun 24, 2012 by TDVT
	2000 ttr250 wont run (Preview) hi im new to the form just have some ? i have a 2000 ttr250 that was runnung great and now nothing so i pulled the carb cleaned everything put new gas pulled plug and its the wrong plug guy before me stuffed a 12mm plug in it insted or the 10mm so im stuck no hely coll will fix that so i checked fire and have good fi...	swygert27	1	582	Jun 24, 2012 by Aidan
	Any solution for this problem with the chain? (Preview) Hi, I´m from spain and I have a TTR250 from 2005. I have a problem, the dirt enter into the case saver and the pinion, I would like know if anybody have made any good solution. Thanks. Regards.	Nomada_Firefox	2	841	Jun 22, 2012 by Cubber
	quike sproket question (Preview) im currently running 14/52 sprocket set and was wondering which way to go on the rear or front sprocket to get a bit more acceleration. not so worried about top speed as on the trails id be lucky to get abouve 70km (most of the time alot lower ). thanks	Aidan	5	923	Jun 19, 2012 by Aidan
	B&B frame guards (Preview) Anyone seen these in the flesh or actually have them fitted? http://www.demonmx.co.uk/contents/en-uk/d281.html	colin13846	12	2713	Jun 4, 2012 by Aidan
	help please bike "chokes" over a certain incline (Preview) Gday Folks . Soaked & cleaned out the carby recently. All good but now when i ride up & over a certain incline (about 30 degrees) the bike starts "choking". Any suggestions really appreciated (even fat jokes accepted ha ha)	BingleBerries	6	1213	Jun 1, 2012 by alainttr250
	Newbie here needs help with TTR not starting (Preview) Hi everyone...new to TTR forum, go easy on me! :) Riding the TTR250 the other day I was going full throttle then it died and sputtered to a stop. I noticed right away the battery was smoking and was EXTREMELY hot to the touch. I got away from it to give it time to cool down...acid explosions are not fun. 2...	Jell	5	879	Jun 1, 2012 by Jell
	05 ttr250 makes an awful clunking (Preview) My 05 ttr 250 makes an awful clunking noise when it cranks and often repeats it when I shut it off. Anyone have this happen before that can tell me what to replace?	davecampbell	7	1274	May 24, 2012 by davecampbell
	What type of fuel do you run? (Preview) I have just started to run 95RON as apposed to 91RON Unleaded in my 97OE, the bike certainly runs better and cleaner i.e. no soot, but has been difficult to start electrically when cold. I don't have a hope in hell of kick starting it. Could this be the fuel or has something else eventuated?	JuJu	10	2763	May 22, 2012 by Cubber
	Rear chain block/stay/guide fingy? (Preview) Stopped on a ride today and noticed there was no rear chain block/guide/stay fingy. Bolts up at the rear of the swingarm. Am I tempting death by running without it, does anyone have one in Orstraya mate. There is one in the USA on Ebay for around $37Au delivered but prefer to keep things local, if anyone...	Gcorner	3	1847	May 21, 2012 by Gcorner
«First < 1 … 56 57 58 59 60 … 66 > Last» \| Page of 66 sorted by