Just out of curiosity, I'm wondering what size pilot jets you guys are using in your ttr250's. I know that the 52 and 52.5 pilot jets seem to work good for a lot of people. Anyone using anything bigger? How about smaller? At what elevations? Any mods to justify?
everyone said they were loud but wow lol after 10mins my ears were ready to bleed I think it's gonna be going back on eBay My last bike was a drz400sm with full yoshi system and it didn't sound this loud. drz sounded awesome the ttr sounds crap :( is there any tricks to make 'em a bit quitier ? It's a 2 month...
kgoose89 wrote: Ok I'm new here sorry if I'm not in the correct area. First off, I purchased a 2000 model ttr250 for 300 dollars. Cleaned the valves, tore everything down. Everything looks fine. I put everything back together, set timing etc. I went to start it yesterday, I've got spark but not sure if t...
Going off the previous guys post about the oil leak seen here. I have ordered the replacement cap but the retaining bolt ive got it also leaking, I think its stripped. It wont tighten down at all. Does anyone know what part number or what kind of screw this is? Mine looks slightly different then the one pi...
Hi for sale enduro tank bag tank panniers and e12 rear panniers £150 plus uk postage, located Surrey . Adrian now includes a fender bag as well -- Edited by noeyedear on Monday 25th of August 2014 05:38:53 PM-- Edited by noeyedear on Wednesday 10th of September 2014 03:31:28 PM
I was cleaning some axles and snail cams this morning and came across two snail cams different to all the others. These have raised corners as shown in the pic above. All my others are dead flat. It may be a coincidence but I have just one Raid axle (shorter than the OE ones) so am guessing they go together...
hi has anyone got a good condition lowering link for sale.i recently bought what was supposed to be one on ebay but it is exactly the same size as the standard one on my 2011 ttr and obviously makes no difference to the height of it whatsoever.
Hey guys. I recently had my bike in at the shop and they told me my starter clutch is wearing that's why I have a clunk when starting. I asked for a quote on the parts new and there so expensive considering what they are. Has anyone got any wrecks/parts in Australia on here that can help me out???
Hi,my brake light was staying on all the time so i checked the foot brake switch and all was well.However i removed the front brake switch and when i push the little pin it goes out.I dont see any way of adjusting this, is it just worn and needs replacing? Thanks in advance Lindsay
I'd like to get a spare rear wheel that I can equip with a different tyre and sprocket for differing conditions/events. Anyone have a spare they'd be prepared to part with for a requisite number of beer tokens? Thanks Simon
The parts are from a working 1992 open enduro. I can send pics. Engine minus starter Front & rear wheels with tyres - rear sprocket ok Frame with numbers Headstock Wireloom Keys & block Chain (new) Gaiters (new) Chainguard Top fairing with light Sidestand Pegs Levers (new) Tank/panels/tai...
It was my last bosses birthday on the 22nd, he hired the track from 10am to 3pm. He invited me along, so the TTR got to stretch her legs for the first time in a while. After high-siding on the 14th, I got onto Brian to sort me some bits, just about fitted them in time for the day. Got my new tyres fitted and the...
Well gotta thank this awesome forum again, had a leaking rear shock so pulled it out and sent it off and rebuilt the carby while I was at it. What a difference that has made as well. Moved the clip a notch, new seals and diaphragm. So easy doing all the above once I read all the stuff on here. Just great. ...
Hey guys I just got a ttr 250 99 model and its hard to start when cold. I changed inlet manifold as it had come Apart now still having same problem. Ideas please ???
Well it would seem that there aren't any frames going in the UK and given that I have a cosmetically challenged (f%%**d) frame does anyone know if a ttr 225 frame will except a 250 engine or do I have to start cutting and doctoring the original ? REGARDS RIPPER
Hi all, The front brake lever of my old TTR is broken, allowing to be actioned only by 2 fingers. Adding to that, it seized the fluid return 2-3 times. Is the full mechanism easy to find ? not very expensive ? (shipped worldwide, or at least to France), or should I still try to replace master cylinder with a...
Hello everyone here. Following friends' advices, last year I bought an old TTR250. According to the frame number it should be '93. It ran quite well for 5 months or so, then it became harder and harder to start. Also I felt lack of compression once the engine gets hot. I was reading through topics here fo...
I've developed a grinding rattling metallic noise fromm around the engine sprocket - gearbox aria when riding,could it be gearbox bearingss, if so does this mean a complete engine strip, rest of engine runs as sweet as a nut,HELP
Hey guys I'm new here just signed up after reading so much useful info on here. I recently bought a ttr 250 1999 model. After riding it a few times it got harder to start when cold. I pulled the carby out and cleaned it and the spark plug, replaced inlet manifold as it has come apart. But its still hard to star...
Hello to all, I enjoyed this forum more than my TTR so far! This because I want to give it a global checkup first. It is a 2006 model and still in good shape. Some carb setting issues to tackle, some fine tuning and off I go .... -- Edited by Spietfriek on Friday 22nd of August 2014 03:14:14 PM
Rare opportunity to buy a 2006 Yamaha TTR250 trail bike that has had a frame up rebuild!Reliable and economical 250cc four stroke with 6 gears - the perfect dual purpose commuter/trail bike.First registered March 2006.MOT (full MOT – not a “daylight" one) until 12th May 2015 and taxed to e...
does anyone have sidestand as i want one to cut down and try. i have the lowering link fitted and a couple of inches of the seat foam removed. i can just about touch the ground when sitting on the bike but when it is on the side stand am having difficulty getting on and off the thing! It is trying to get my le...
Trying to get at the starter gears and motor and have found 2 out of the three cover bolts sized. Have cut slots to try remove with no luck and am running out of options before I have no choice but to drill them out. At least the holes are through drilled so I should be able to clean them out. Anyway, Rant o...
