Hi All, Does anyone know what size crow foot spanner Brian used to hold the flywheel whilst undoing the flywheel retaining bolt. I can't read it on the photographs and need to remove the flywheel. If you're out there Brian can you remember the size?? Gruf.
Hi all, I've just joined so hello. Great forum. I gave up biking 20 odd years ago and have just returned and I'm well impressed with the quality of info in this forum. When I was biking the internet had not quite grown - so no real forums. But I've been using car forums and the info here is really a different c...
hey folks, just bought a ttr and, after a short ride im sure all's not well within the engine cases so iv found this forum and hopefully, with your help obvs lol, i will be able to get to the bottom of it cheers chris
Hi guys, Just a few pictures of my work done on my TTR in order to get a new appearance and voice. -- Edited by balin01 on Thursday 15th of June 2017 10:27:34 PM
Hi All, I have a 1999 TTR250 with 15000 km on the clock. After realising a few drops of oil each time I parked, I decided to replace the sprocket seal. When I noticed that the problem was still thee, I went for the talcum powder and noticed it was coming from the rubber grommet that holds the wires into the a...
I am new to the TTR as I just bought a 99 TTR-250 a couple months ago. I know there are many topics about this but I just can't seem to find a straight answer. My plastics are in bad shape, especially the fenders. I have found some front fenders that will work with a little drilling but can anybody tell me if th...
Hi, Soon I shall be stripping down my TTR and removing the Kouba lowering link, would anyone care to swap an original one for this part please? Less than 1000 miles gentle green laning done (Bike only covered 2200)
My ongoing garage clear out continues and I have got to the headlight box! I have some Acerbis headlight units for sale on eBay. Although not specifically made for the TTR, they were taken off TTR250s that I broke for spares and put the headlights back "just in case". If you are taking your TTR offroad fo...
Hi I'm Steve from Hereford... I've got a 53 plate ttr250...well impressed with it...although it's not running 100%... I'm unable to adjust the air mixture screw(it's been butchered)....so I'm after another carb... if anybody could help out, it would be much appreciated thanks Steve.
Picked up the full graphics kit from Enjoy that included the new seat cover. Pretty good kit and was not too difficult to install. Had to trim a bit of the graphic on the gas tank as I couldnot get it to lay right around the edges. before after
Hi All, Im all the way from South Africa, any other SA guys here? Just bougth a TTR 250, Been riding a Vertimati Motard the last couple of year, and saw a TTR, and though i must have it. Been snooping around the Forum for over a week now, and decided to join in on the Fun. Anyway, long story short. Bike i bo...
I have picked up a rolling chassis as a possible next project. I want to check if a TTR engine will shoehorn into the frame and, if not, whether the wheels and front forks can be used Brian
Just when you thought it was safe, I have started another refurb As usual, ICS at Cullompton did a great job on the powder coating and I have so far loose-fitted the wiring loom plus rec/reg, coil and solenoid. I am trying to recall the best order in which to fit the parts and think it's linkage and swing a...
Hey guys, I've got a 98 1.8T. I've had a k04 and chip for a while and wanted to get more performance. I was recommended to port and polish the intake and exhaust. We found out they used abrasive material to do it like gritty sand. So I got with my friend that tunes Hondas and we decided to try it ourselves. We...
The faq said yz plastics fit but i dont see any year that will fit my 04. Are there any side plate options that will fit the side size properly with light modification to the mounts Perhaps?
Hi guys. Anyone thought about fitting a WR motor into a ttr frame? Besides he engine mountings and radiator position, it might just work? The thought crossed my mind as I saw a wrecked WR 250 with low km on it. You thoughts???
For owners of blue TTRs, a simple upgrade is to fit footpegs from the older white model. The blue pegs are 30mm wide and the white ones are 37/38mm wide. The wider ones fit straight in Hope that helps someone. I have not been able to source a sensibly priced set of after-market wide pegs Brian
Hi every one, I just bought my first 2011 TTR250 with 520km on the clock! I know good find right! Don't worry it cost me a pretty penny to have it shipped interstate. I just took off all the blinkers and number plate holder as it will be used for dirt at this stage. Anyway I was just wondering if anyone can tel...
Just like to say a big thank you to all of you who have supported the shop over the last year. We have really enjoyed our first year and look forward to many more And a big thanks to Brian and Trish who's continued help is much appreciated. Steve & Lisa
Well summers here Lot's of the lanes are Brambles and over grown and very dry we are having a mini Heat wave. It's time to pull the Beast out of it's winter slumber an hit the Tarmac A quick clip from yesterdays trip out round the Moor a pint an a pasty for dinner and home some 80 miles. https://www....
Due to a lack of funds it looks like the TTR will be getting just a tart up this year. Once the engine is out I can then start prepping the frame. Started today just got the engine bolts to come out then lift the engine out for the strip down. The bottom mount looks a bit of a pain to remove. Heres a couple of pic...
Hi I'm after a Right (as you are sat on the bike, offside) plastic panel. Does anyone have one spare please? I will take a complete set if its easier Regards Rod
Thought I would give the TTR a bit of TLC today Threw a pair of new D606's on, I was going to fit them onto the WRR but ordered a set of MT21's for the WRR. The D606 have been to the Flinders twice plus local rides so happy. I've washed the bike 3 times since the Flinders trip & it was still dirty, degreased i...
Been looking at the site for a few days.. tons of good info for the average skilled gearhead. Hope to have the bike running in the next 24hrs thanks to info on the Carb section. Thanks for the info!
