Not seen this here....maybe its tucked away somewhere? I have used this for setting my gearing for Snetterton on my GSX-R600 and it worked perfectly well...it's very comphrehensive the first time takes a while but once saved its a peach of a program. enjoy http://www.gearingcommander.com/ -...
It's always difficult drilling holes for the number plate screws in thin plastic flexi plates. I tried a different approach this morning using a 6mm hollow punch and it worked a treat. I didn't take photos as I did it as I was too keen to see how effective it was! However, here is an "after" photo with jus...
No idea what its from. It's been hiding in the bottom of a box for a decade or so! Collect or will post at cost. Otherwise, does anyone recognise which bike it fits? Brian
Hi there. Just recently got myself a ttr and it rums a fcr33. I have just took it off to clean it out as it overflows if the engine is switched off and fuel is on. Does anyone else have experience of these carbs? If so what jets do you use and have you any advice?
Would someone be so kind as to put up a digital picture of these arrows and alignment marks? I must be blind because I do not see any arrows or alignment marks. Also how thick are the friction plates supposed to be? What about the steel plates? My steel plates are visibly worn and one (perimeter) edge...
When lugging at low RPM I'm getting a weird backfire and motor stall that sounds like it's coming out of the header. Is this normal or maybe timing chain or something? The carb is freshly rebuilt and otherwise runs great when not idling. Stock everything (US 1999 model). Unknown time on the motor. It w...
Hi there, anybody knows the number of part of the cylinder gasket, and the cylinder head gasket in the Open Enduro models? is the same that the y2k models? I have an Open Enduro TTr, but I don't know the year, it doesn't have the VIN number, and the chassis is 4GY-085589, maybe '97- '98 or '99, i´m not shu...
just noticed shocker & bottom of engine wet it is black eng oil the bottom of the round breather is wet at the pipe that faces downhill but it is flattened at the end took off air box cover it is dry inside bike runs fine starts ok no smoke out of exhaust even on over run so no guide or stem seal problems t...
Oil Filter All balls headstock bearing kit. top and bottom Brand new front pads. £30 the lot. Delivered (If payment made by paypal gift) -- Edited by TTRHead on Monday 27th of June 2016 07:40:54 PM
I get so much crap about this bike from guys who still ride crotch rockets, like my buddy Ken. The YZ has a little more punch, just a little. But it doesn't slow down any faster -- at the end of the vid Ken took out a barb wire gate (they are hard to see) and got a little tangled up in the fence. I slowed down th...
went out with my son tonight first 20 mins i was off. got in a rut was not riding fast enough got up carried on we did 62 miles on / off road was good though need to get out more could not get used to riding on road with off road tyres seems wierd but more time i wil get used to it
Hi, I keep looking at those two angled flat surfaces either side of my rear mudguard and wonder, is there a suitable flush or fairing type indicator that would fit there neatly? Any advice would be welcome. Robin.
Evening all, thought I would introduce myself been on the forum for a little while lurking for a TTR managed to pick an 05 model up at the weekend from essex. Bikes got less than 4k on it. Was originally looking for an OE but decided to dig in the pockets and spend a little more on a newer model. I'm from Nantw...
Just though I'd say hello to everyone as I'm new on the forum Had a 93 250 for about 2 years now and love it , mostly use it to commute on in the winter when the show pony sports bike is scared to come out and play
Hello all ....I'm new to the group ....I've owned a 99 ttr250 for about 2 weeeks now ....I bought it non running with no wiring harness basically (original one was rigged up some crazy way) .....so I grabbed my multi meter and downloadded manual ....I checked every thing and ended up replacing the igni...
I have a slight oil leak when trying to get my Ttr to start.....it's leaking from the metal piping that's connects the top end to bottom end .....the bolt it's right below the exhaust pipe on the right side just above the oil filter housing I believe ....any ideas on how to stop it from leaking ? Should I ta...
Hi, I have a 1997 250 Raid and over the last 2-300 mile the gear change from 1st to neutral has become very stiff and am now at the point where it just wont go at all unless the bike is off, even pulling away and going for 2nd is becoming stiff? Has anyone had this issue or knows what the problem might be? and an...
I have posted before about my ttr not working after about half throttle as it ran pretty good once I got it and cleaned it up and went through the carb it would go all the way now just recently will not. I thought it was running to lean so I had a custom sigma 6 jet kit built for the make model year and elevatio...
i am looking for 2 rear wheel spacers for my oe i have fitted rear w brgs and found out small play in spacers into brgs would like new but on a budget need to get it on road for mot many thanks john 07961904435
Arrows points to mods, oil cooler , rear disc gaurd , led saftey light , standard tailpipe mod, home made bashplate , tool bag ( which is a shaving / toilet bag) , shortened rear visIon mirrors ,
im in need of new ones, but none listed in the shop, anyone know where i can buy them? base gasket needs done so started stripping the bike, exhaust studs are wrecked, but atleast they cam out, they are rusted solid to the nuts so im in need of the full stud and nut.
Hi All Long time lurker, must say its a great site full of info and helpful people. I currently have 2 ttr250's both the blue models,one is just the daily farm run around bike the other is been turned into a lighter little faster weekend bike for the bush. I have the air box out of the build bike atm and i'm ju...
Been fiddling around with the jetting on my 325 recently as I've got the loan of an Air/fuel ratio meter and header pipe with lambda sensor boss. (Oh, and I've got no wife/kids/life ) The 325 runs nicely on 50 pilot/147main jets, needle clip 1 notch above middle. Motad exhaust, Twinair filter and mild...
Ridelimousin are pleased to announce the launch of our brand new website! After weeks of hard work and dedication, we are delighted to officially announce the launch. The new site is available at the same address and has some cool new features such as a youtube video gallery showing some of the recen...