2004 model. 4 previous owners. I have owned this since 2010 from a friend. He had bought it from a local dealers where I live. I bought it with 2200 miles on the clock with all the road gear still on it - it had not been used off tarmac. Since 2010 I have used it for what Mr Yamaha intended it to be used for - trai...
Got it on ebay from China for $5 au. since i have aheadlight switch fitted i thought i run this LED light permantley with the key on. Guess its more show than go but itdoes look effective close up. Its like a park light or something to tell me the ignition is on. May look into buying a CREE LED light which is 6...
All straight and true. Including number plate the bike has only had 2 previous keepers. Registered to me at my address. HPI clear someone make me an offer. -- Edited by TTRHead on Wednesday 27th of July 2016 07:44:38 AM
I have been playing with jets on my 1996 Raid lately. My bike has the snorkel out, no restrictor. Before it ran fine, but the first 1/4 was weak so I changed the #50 pilot to a 52.5. The new power was instantly noticeable. However, beyond about 1/4 -1/3 it weakens for a bit, then picks up again. Every singl...
Not seen this here....maybe its tucked away somewhere? I have used this for setting my gearing for Snetterton on my GSX-R600 and it worked perfectly well...it's very comphrehensive the first time takes a while but once saved its a peach of a program. enjoy http://www.gearingcommander.com/ -...
It's always difficult drilling holes for the number plate screws in thin plastic flexi plates. I tried a different approach this morning using a 6mm hollow punch and it worked a treat. I didn't take photos as I did it as I was too keen to see how effective it was! However, here is an "after" photo with jus...
No idea what its from. It's been hiding in the bottom of a box for a decade or so! Collect or will post at cost. Otherwise, does anyone recognise which bike it fits? Brian
Hi there. Just recently got myself a ttr and it rums a fcr33. I have just took it off to clean it out as it overflows if the engine is switched off and fuel is on. Does anyone else have experience of these carbs? If so what jets do you use and have you any advice?
Would someone be so kind as to put up a digital picture of these arrows and alignment marks? I must be blind because I do not see any arrows or alignment marks. Also how thick are the friction plates supposed to be? What about the steel plates? My steel plates are visibly worn and one (perimeter) edge...
When lugging at low RPM I'm getting a weird backfire and motor stall that sounds like it's coming out of the header. Is this normal or maybe timing chain or something? The carb is freshly rebuilt and otherwise runs great when not idling. Stock everything (US 1999 model). Unknown time on the motor. It w...
Hi there, anybody knows the number of part of the cylinder gasket, and the cylinder head gasket in the Open Enduro models? is the same that the y2k models? I have an Open Enduro TTr, but I don't know the year, it doesn't have the VIN number, and the chassis is 4GY-085589, maybe '97- '98 or '99, i´m not shu...
just noticed shocker & bottom of engine wet it is black eng oil the bottom of the round breather is wet at the pipe that faces downhill but it is flattened at the end took off air box cover it is dry inside bike runs fine starts ok no smoke out of exhaust even on over run so no guide or stem seal problems t...
Oil Filter All balls headstock bearing kit. top and bottom Brand new front pads. £30 the lot. Delivered (If payment made by paypal gift) -- Edited by TTRHead on Monday 27th of June 2016 07:40:54 PM
I get so much crap about this bike from guys who still ride crotch rockets, like my buddy Ken. The YZ has a little more punch, just a little. But it doesn't slow down any faster -- at the end of the vid Ken took out a barb wire gate (they are hard to see) and got a little tangled up in the fence. I slowed down th...
went out with my son tonight first 20 mins i was off. got in a rut was not riding fast enough got up carried on we did 62 miles on / off road was good though need to get out more could not get used to riding on road with off road tyres seems wierd but more time i wil get used to it
Hi, I keep looking at those two angled flat surfaces either side of my rear mudguard and wonder, is there a suitable flush or fairing type indicator that would fit there neatly? Any advice would be welcome. Robin.
Evening all, thought I would introduce myself been on the forum for a little while lurking for a TTR managed to pick an 05 model up at the weekend from essex. Bikes got less than 4k on it. Was originally looking for an OE but decided to dig in the pockets and spend a little more on a newer model. I'm from Nantw...
Just though I'd say hello to everyone as I'm new on the forum Had a 93 250 for about 2 years now and love it , mostly use it to commute on in the winter when the show pony sports bike is scared to come out and play
Hello all ....I'm new to the group ....I've owned a 99 ttr250 for about 2 weeeks now ....I bought it non running with no wiring harness basically (original one was rigged up some crazy way) .....so I grabbed my multi meter and downloadded manual ....I checked every thing and ended up replacing the igni...
I have a slight oil leak when trying to get my Ttr to start.....it's leaking from the metal piping that's connects the top end to bottom end .....the bolt it's right below the exhaust pipe on the right side just above the oil filter housing I believe ....any ideas on how to stop it from leaking ? Should I ta...
Hi, I have a 1997 250 Raid and over the last 2-300 mile the gear change from 1st to neutral has become very stiff and am now at the point where it just wont go at all unless the bike is off, even pulling away and going for 2nd is becoming stiff? Has anyone had this issue or knows what the problem might be? and an...
