|
Rear rack
(Preview)
I want to get a rear rack for my TTR. There seems to be 4 rear racks commercially available: B&B, Whipps, Cycleracks and Ventura, though the Ventura is expensive when bought without a bag. B&B Whipps Cyclerack Ventura The Whipps one seems the most appealing to me, for attacthing tie downs etc...
|
Matt
|
3
|
4794
|
|
|
Starting problems
(Preview)
I've just finished checking the cylinder head of my TTR after a worry some grit got in when I removed the spark plug. There was a bit of fine grit/sand on the crown of the piston but the valves 'seemed' to be clean and were seating ok. After the rebuild, the bike initially started but stopped after a coupl...
|
Wee Jessie
|
4
|
1455
|
|
|
Mystery object!
(Preview)
I recently bought a TTR for spares and found this little device on the handlebars. The pipe was fixed into the airbox. It looks like an ordinary tyre "air bomb" that has been adapted but, what for All that remains of the sticker on the cannister is a large red F My thoughts are that it was a devi...
|
TTRfan
|
3
|
1465
|
|
|
still no tail light
(Preview)
i put a hydrolic switch back to my tail light, i disconnected the yellow wires, and ran my hydrolic in between the two yellow wires, and have the blue and black wires unchanged. I cant seem to get a constant tail light action, but the brake light works just fine. How do i get a running light, and a brake lig...
|
nwrider
|
6
|
2661
|
|
|
Carb issues - occasional sputter
(Preview)
Hey guys. New to the forum! I tried a search for this topic but didn't find what i was looking for. I appreciate any help. I just purchased a 2006 TTR250. Couldn't keep it idling without high rev. I drained the tank (removed it, turned it upside down and rinsed with new gas). I removed the carburetor, pull...
|
cbass68
|
4
|
4898
|
|
|
Splitting the forks
(Preview)
I'm going to get my fork lowers powder coated so need to split the forks on my raid. As I don't want to get smashed in the face with anything under pressure what's the procedure to get the forks apart? Is it the large allen screw from underneath or do I go from the top. I don't want to strip the fork internals i...
|
spud351
|
12
|
1597
|
|
|
Repacking
(Preview)
how often do i need to repack my stock 06 muffler, are there queiter mufflers out there, i am think about going to a fmf q4, If i do this what kind of jetting do i need to do?
|
nwrider
|
3
|
1488
|
|
|
UK owners - obtaining valve shims
(Preview)
Unlike the originals, the after-market shims are in intervals of .005mm or is that 0.05…. but that is usually sufficient to get the clearance within specification.The TTR shims are 9.48mm in diameter and these guys do them for £2.85 each inc. p&p - http://cgi.ebay.co.uk/VALVE-SHIMS-CRF-R...
|
TTRfan
|
1
|
1237
|
|
|
WOODRUFF KEY
(Preview)
THE TTR STALLED LUCKILY AS I JUST GOT HOME.IT WOULDN'T RESTART SOUNDED LIKE THE STARTER WASN'T ENGAGING. ON INVESTIGATION THE BOLT HOLDING THE GENERATOR SECURE WAS LOOSE,REMOVED GENERATOR FOUND THE WOODRUFF KEY HAD SHEARED! REPLACED THE KEY.THIS KEY IS 5MM THICK SO? CHECKED TIMING THE CAMS WERE O...
|
tracker
|
2
|
1444
|
|