A forum for owners of Yamaha TTR250 trail and enduro bikes!

Thomas ttr250 Williams · Thomas ttr250 Williams

hiya all I'm looking for someone to be able to get my ttr running properly again . Will deliver to you depending how long a drive it is . my father purchased this bike around 4-5 years ago was using it regular then it needed a mot so he never bothered with it again . After 3 years of being dry stored ive decide...

DANKWHEELIE420 · DANKWHEELIE420

I WANNA KNOW IF I CAN ENHANCE AND GET SOME SEXY BULLETPROOF GOODIES 4 MY TTR 350 STOCK ISNT ENOUGH

Dave · Dave

Hi all, I'm new to the forum - I've got a 2002 TTR250 which has developed a bit of a cold starting problem. Essentially, I usually turn the fuel on, choke out, then use the electric start and it fires up after a couple of seconds holding the button. Recently though, it just turns over and will not fire up f...

katana · katana

I am busy reading the repairs thread - finished the carb one earlier. I have an odd issue. It only happens in 6th gear, usually while overtaking a car. I will be going strong, when all of a sudden I get a splutter in the revs, almost like running out of fuel. When I change to 5th, I can rev strongly with no h...

Gcorner · Gcorner

The Missus just passed her competency test for pre learners (Tasmania) and is keen to start riding the TTR to work so i was wondering if anyone knew how to lock up the tank for some added security, more concerened about vandals and skanky additives than pilfered fuel. Fuel is easy to replace. Probably...

diggermanbob · diggermanbob

hello all , does anyone know of a comfortable seat I can buy fir my blue ttr , I took it out yesterday for ride up to the ABR rally at Banbury , really pleased with the little bike , I did bin it on the enduro course forgetting I wasn't on my xt660 and didn't give it enough beans up a very steep hill , almost made it...

TTRfan · TTRfan

On my way to meet up with some mates for a trail ride earlier in the week, there was a death rattle coming from the 325 that prompted me to turn around and head back about 3 miles from home. Really disappointing as I don't get out much these days and the ride was in the Dawlish area and haven't ridden those lan...

oneece · oneece

Hi all, First off, a quick introduction. I’m Ollie, and I’ve had my TTR for a while now (a year or 18 months, can’t remember exactly). It’s a K reg metal tank version. I use it for green laning so it gets a bit battered and bruised, but I always give it a lot of TLC after each trip! There’s one slightly odd f...

Markvan · Markvan

The old beach ridden bars replaced by a resprayed set. Only major job the beast has had its entire life is a camchain. Uses no oil , just a couple of puffs of smoke on start up after sitting for a week.

TTRfan · TTRfan

Sorry about the bad pun but I have spent a few hours this afternoon trying to sort out a TTR250 front brake master cylinder and it's sort of making me feel a bit hysterical My mate Jim has a collection of shiny chromed up vintage(ish) Jap bikes and spends quite a bit of time fettling them and trying variou...

charlesrobertson · charlesrobertson

Police rang me and said they found my stolen ttr supermoto from months ago, so so happy Quite a bunch of stuff to fix, including a new seat but happy it still runs and rides. Going to fix it back up and this time get insurance, a tracker, and multiple locks

iantomich · iantomich

Anyone one a fix for this 93 airbox,bolts sheared,drilling heated the nut up, nut turned, should not be a prob bonding it with an adhesive and clamping up for a few days,nut size is 6 mm diameter, length of nut is 15 mm, 12 mm arrows the flats and closed at one end,open would be ok,I've seen connector nuts w...

Juvecu · Juvecu

I'm taking my forks apart because one of the stanchions is bent from a bad fall I had in Portugal. I need a special tool to take it apart and although it's possible to do it without, I prefer to know it's done properly when I put it back together. I have an alternative reason here for wanting a tool, I recentl...

Benjah · Benjah

My TTR250 stock exhaust has a distinct bend/kink where the stainless trim covered pipe section joins the main body of the exhaust. Are they meant to be like this or are they supposed to be straight? -- Edited by Benjah on Thursday 21st of September 2017 01:03:57 AM

vinnie · vinnie

Went through a few fords last weekend and have hit some deep-ish puddles in the past, although I don't think I've actually gone over the hub... Are there any checks/maintenance procedures tips/tricks that can be carried out from time to time to easily and simply check for corrosion, re-grease, etc...

Moo · Moo

Anyone got any tips for when I eventually take this lot off and renew it all. It is rusty as well, i'm expecting the nuts to jut crumble when any force is applied. I'll probably use a nut splitter to get them off. Main worry is the studs snapping off in the head. Been spraying with wd40 everyday so hopefully...

TTRfan · TTRfan

I am working on another refurb where the exhaust is perfectly sound but the stainless steel guard (decoration!) has been badly marked. The guards are held in with four rivets and are easily removed to allow the exhaust to be properly cleaned and painted. I took the old stainless steel guard along to m...

TTRfan · TTRfan

I bought a kit through eBay (they are still being sold - see here) back in 2012 with high expectations of restoring all the nuts and bolts on my refurbs and making them look proper "factory" but the kit and instructions looked a bit complex so I kept putting off using it - until today I was right in thinkin...

Jumpn · Jumpn

a couple new additions to my TTR. Tusk handguards, Ricochet skidplate.

katana · katana

Hi all My bike's PO told me to drain the valve on the oil breather line regularly. I was worried it was due to blow by, but I checked it today - +/- a week since I checked it last and +/- 50km - and I found a milky, mostly water mix in the drain nipple(?). If this was a water cooled engine I would be crapping myse...

69chris · 69chris

hey guys, just bought a ttr and, after a short ride im sure all's not well within the engine cases its noisy....as in it rattles at certain revs, couldnt decide if its a cam chain rattle, valve clearances or piston noise....or something worse !!! whipped of the valve cover, set it to tdc and found that...

katana · katana

I want to get a bit more flow through the stock silencer. I read on another forum about making a hole next to the std hole in the tin can piece. It apparently misses some baffling that way and is not too noisy. Can anyone confirm that it is so? Some idea of the internal layout of the baffling would be grea...

leigh · leigh

Haven't watched it all yet, but I'm sure it will come in handy for someone. https://www.youtube.com/watch?v=KW0CwkOtKBA

katana · katana

I am still busy reading and searching, but I thought I would put this out there so long. I was quite surprised when the new to me TTR felt like it topped out at 80km/h. This bike was well looked after cosmetically, but mechanically not so much - i.e. loved but not understood The bike takes forever to cat...

Jumpn · Jumpn

My son washed out the front end of the TTR, now the forks and handlebars are not aligned. The bars are favoring the right side of the bike. Do I need to loosen to the headstem bolt, or do I start with the triple clamps and front axle? I would appreciate your kind assistance with this. Thank you.

TTRfan · TTRfan

Nasty weather here today so decided to spend some workshop time on carbs put back over the years for various reasons. A couple of them had seized float bowl drain screws - not unusual - so had a go with my LH drill bits and Easy-outs. This screw was not going to come out without a fight Tools used plus a LH d...

Base · Base

Can anyone off the top of their head or if they happen have one lying around handy, give me the dimensions of the rear shock, A. eye to eye B. Overall length C. Bolt hole size both ends D. The distance between the clevis end forks. Regards, Cam.

Wally Wombat · Wally Wombat

Hi all, One of my bikes seems mysteriously clunky when shifting gear. Cant work it out. Rode my 315 yesterday and it was silky smooth in comparison. Can anyone offer any advice? I have changed the oil. Clutch lever seems properly adjusted. Am looking for clues and it seems it is clunkiest when the bike...

jaja · jaja

A few months ago my 2011 model TTR-250 had a flat battery. Bought new battery. 3 weeks later flat again. Brought it to an independent mechanic. He said "needs new regulator". Charged me A$280 for new regulator + labor and he charged the battery. 3 weeks later flat again. He said "battery probably damag...

andy63 · andy63

Hi, Just noticed the bottom of the rear shock is rubbing on the swingarm cross member. Any ideas as to why it might be doing this? Will adjusting the shock stop it happening??

Topic		Started By	Replies	Views	Last Post
	Help with 2005 ttr250 (Preview) hiya all I'm looking for someone to be able to get my ttr running properly again . Will deliver to you depending how long a drive it is . my father purchased this bike around 4-5 years ago was using it regular then it needed a mot so he never bothered with it again . After 3 years of being dry stored ive decide...	Thomas ttr250 Williams	2	484	Oct 25, 2017 by Thomas ttr250 Williams
	CAN YOU USE TT 600 PARTS ON THE TTR? (Preview) I WANNA KNOW IF I CAN ENHANCE AND GET SOME SEXY BULLETPROOF GOODIES 4 MY TTR 350 STOCK ISNT ENOUGH	DANKWHEELIE420	3	602	Oct 22, 2017 by petenz
	Cold Starting Issue (Preview) Hi all, I'm new to the forum - I've got a 2002 TTR250 which has developed a bit of a cold starting problem. Essentially, I usually turn the fuel on, choke out, then use the electric start and it fires up after a couple of seconds holding the button. Recently though, it just turns over and will not fire up f...	Dave	30	4001	Oct 21, 2017 by TTRed
	Misfiring in top gear (Preview) I am busy reading the repairs thread - finished the carb one earlier. I have an odd issue. It only happens in 6th gear, usually while overtaking a car. I will be going strong, when all of a sudden I get a splutter in the revs, almost like running out of fuel. When I change to 5th, I can rev strongly with no h...	katana	9	764	Oct 20, 2017 by katana
	Locking fuel cap for a plastic tank? (Preview) The Missus just passed her competency test for pre learners (Tasmania) and is keen to start riding the TTR to work so i was wondering if anyone knew how to lock up the tank for some added security, more concerened about vandals and skanky additives than pilfered fuel. Fuel is easy to replace. Probably...	Gcorner	17	1919	Oct 20, 2017 by ttr steve
	Comfortable seat for standard ttr (Preview) hello all , does anyone know of a comfortable seat I can buy fir my blue ttr , I took it out yesterday for ride up to the ABR rally at Banbury , really pleased with the little bike , I did bin it on the enduro course forgetting I wasn't on my xt660 and didn't give it enough beans up a very steep hill , almost made it...	diggermanbob	24	4873	Oct 20, 2017 by diggermanbob
	Well, that explains the rattle! (Preview) On my way to meet up with some mates for a trail ride earlier in the week, there was a death rattle coming from the 325 that prompted me to turn around and head back about 3 miles from home. Really disappointing as I don't get out much these days and the ride was in the Dawlish area and haven't ridden those lan...	TTRfan	4	727	Oct 16, 2017 by ttr steve
	Bike cuts out after sat at constant revs! (Preview) Hi all, First off, a quick introduction. I’m Ollie, and I’ve had my TTR for a while now (a year or 18 months, can’t remember exactly). It’s a K reg metal tank version. I use it for green laning so it gets a bit battered and bruised, but I always give it a lot of TLC after each trip! There’s one slightly odd f...	oneece	5	570	Oct 14, 2017 by oneece
	Approaching 50,000km (Preview) The old beach ridden bars replaced by a resprayed set. Only major job the beast has had its entire life is a camchain. Uses no oil , just a couple of puffs of smoke on start up after sitting for a week.	Markvan	3	743	Oct 11, 2017 by Markvan
	Don't go braking my heart! (Preview) Sorry about the bad pun but I have spent a few hours this afternoon trying to sort out a TTR250 front brake master cylinder and it's sort of making me feel a bit hysterical My mate Jim has a collection of shiny chromed up vintage(ish) Jap bikes and spends quite a bit of time fettling them and trying variou...	TTRfan	1	546	Oct 3, 2017 by JOHNYBOY
	Stolen TTR Found (Preview) Police rang me and said they found my stolen ttr supermoto from months ago, so so happy Quite a bunch of stuff to fix, including a new seat but happy it still runs and rides. Going to fix it back up and this time get insurance, a tracker, and multiple locks	charlesrobertson	7	644	Oct 2, 2017 by charlesrobertson
	Airbox - repair mountings for mudflap? (Preview) Anyone one a fix for this 93 airbox,bolts sheared,drilling heated the nut up, nut turned, should not be a prob bonding it with an adhesive and clamping up for a few days,nut size is 6 mm diameter, length of nut is 15 mm, 12 mm arrows the flats and closed at one end,open would be ok,I've seen connector nuts w...	iantomich	4	821	Sep 25, 2017 by iantomich
	Fork Disassembly Special Tool (Preview) I'm taking my forks apart because one of the stanchions is bent from a bad fall I had in Portugal. I need a special tool to take it apart and although it's possible to do it without, I prefer to know it's done properly when I put it back together. I have an alternative reason here for wanting a tool, I recentl...	Juvecu	9	2187	Sep 25, 2017 by Juvecu
	Stock exhaust pipe bend? (Preview) My TTR250 stock exhaust has a distinct bend/kink where the stainless trim covered pipe section joins the main body of the exhaust. Are they meant to be like this or are they supposed to be straight? -- Edited by Benjah on Thursday 21st of September 2017 01:03:57 AM	Benjah	2	513	Sep 21, 2017 by Benjah
	Bearing maintenance after wet ride? (Preview) Went through a few fords last weekend and have hit some deep-ish puddles in the past, although I don't think I've actually gone over the hub... Are there any checks/maintenance procedures tips/tricks that can be carried out from time to time to easily and simply check for corrosion, re-grease, etc...	vinnie	1	595	Sep 7, 2017 by TTRfan
	Crusty Rusty Exhaust Header and Studs (Preview) Anyone got any tips for when I eventually take this lot off and renew it all. It is rusty as well, i'm expecting the nuts to jut crumble when any force is applied. I'll probably use a nut splitter to get them off. Main worry is the studs snapping off in the head. Been spraying with wd40 everyday so hopefully...	Moo	4	1555	Sep 1, 2017 by TTRfan
	Renewing the stainless steel exhaust guard or trim piece (Preview) I am working on another refurb where the exhaust is perfectly sound but the stainless steel guard (decoration!) has been badly marked. The guards are held in with four rivets and are easily removed to allow the exhaust to be properly cleaned and painted. I took the old stainless steel guard along to m...	TTRfan	11	17960	Aug 31, 2017 by TTRfan
	Zinc/nickel plating using a hobby kit (Preview) I bought a kit through eBay (they are still being sold - see here) back in 2012 with high expectations of restoring all the nuts and bolts on my refurbs and making them look proper "factory" but the kit and instructions looked a bit complex so I kept putting off using it - until today I was right in thinkin...	TTRfan	17	4196	Aug 25, 2017 by katana
	hand guards, skid plate installed (Preview) a couple new additions to my TTR. Tusk handguards, Ricochet skidplate.	Jumpn	0	1500	Aug 21, 2017 by Jumpn
	Water / oil mix in oil breather line valve (Preview) Hi all My bike's PO told me to drain the valve on the oil breather line regularly. I was worried it was due to blow by, but I checked it today - +/- a week since I checked it last and +/- 50km - and I found a milky, mostly water mix in the drain nipple(?). If this was a water cooled engine I would be crapping myse...	katana	3	963	Aug 18, 2017 by ttboof
	annoying.....worrying rattle (Preview) hey guys, just bought a ttr and, after a short ride im sure all's not well within the engine cases its noisy....as in it rattles at certain revs, couldnt decide if its a cam chain rattle, valve clearances or piston noise....or something worse !!! whipped of the valve cover, set it to tdc and found that...	69chris	15	2367	Aug 16, 2017 by anaronix
	Std exhaust diagram / layout? (Preview) I want to get a bit more flow through the stock silencer. I read on another forum about making a hole next to the std hole in the tin can piece. It apparently misses some baffling that way and is not too noisy. Can anyone confirm that it is so? Some idea of the internal layout of the baffling would be grea...	katana	3	498	Aug 14, 2017 by katana
	TTR 250 Engine rebuild video (Preview) Haven't watched it all yet, but I'm sure it will come in handy for someone. https://www.youtube.com/watch?v=KW0CwkOtKBA	leigh	4	995	Aug 14, 2017 by RodYorkttr
	Some Q's (Preview) I am still busy reading and searching, but I thought I would put this out there so long. I was quite surprised when the new to me TTR felt like it topped out at 80km/h. This bike was well looked after cosmetically, but mechanically not so much - i.e. loved but not understood The bike takes forever to cat...	katana	5	1001	Aug 11, 2017 by katana
	twisted forks, how to straighten (Preview) My son washed out the front end of the TTR, now the forks and handlebars are not aligned. The bars are favoring the right side of the bike. Do I need to loosen to the headstem bolt, or do I start with the triple clamps and front axle? I would appreciate your kind assistance with this. Thank you.	Jumpn	3	1351	Aug 4, 2017 by RodYorkttr
	Some you win, some you lose! (Preview) Nasty weather here today so decided to spend some workshop time on carbs put back over the years for various reasons. A couple of them had seized float bowl drain screws - not unusual - so had a go with my LH drill bits and Easy-outs. This screw was not going to come out without a fight Tools used plus a LH d...	TTRfan	1	923	Aug 4, 2017 by RodYorkttr
	Rear shock size (Preview) Can anyone off the top of their head or if they happen have one lying around handy, give me the dimensions of the rear shock, A. eye to eye B. Overall length C. Bolt hole size both ends D. The distance between the clevis end forks. Regards, Cam.	Base	3	2212	Aug 1, 2017 by ttr steve
	clunky gear change (Preview) Hi all, One of my bikes seems mysteriously clunky when shifting gear. Cant work it out. Rode my 315 yesterday and it was silky smooth in comparison. Can anyone offer any advice? I have changed the oil. Clutch lever seems properly adjusted. Am looking for clues and it seems it is clunkiest when the bike...	Wally Wombat	10	1982	Aug 1, 2017 by TTRfan
	still not charging after $410 mechanical bill... (Preview) A few months ago my 2011 model TTR-250 had a flat battery. Bought new battery. 3 weeks later flat again. Brought it to an independent mechanic. He said "needs new regulator". Charged me A$280 for new regulator + labor and he charged the battery. 3 weeks later flat again. He said "battery probably damag...	jaja	11	2413	Jul 30, 2017 by ttr steve
	Rear shock rubbing on swingarm (Preview) Hi, Just noticed the bottom of the rear shock is rubbing on the swingarm cross member. Any ideas as to why it might be doing this? Will adjusting the shock stop it happening??	andy63	47	5963	Jul 29, 2017 by JOHNYBOY
«First < 1 … 23 24 25 26 27 … 65 > Last» \| Page of 65 sorted by