A forum for owners of Yamaha TTR250 trail and enduro bikes!

BikerMat · BikerMat

Hi Totally TTR, I have recently bought a 1993 ttr 250, it's a bit rought looking and upon closer inspection the bike has revealed its rough life. Rant incoming, TL;DR at the bottom. I have a few questions about whats what on the bike, OEM parts, aftermarket replacements and bits that stood out as sketch...

Rooster · Rooster

I've had a few bikes before and generally do my own wrenching. Decided to pick up a dirt bike after leaving road bikes a couple years ago. Paid 900 bucks for this 1999 TTR. The Carb was a basket case. Accelerator pump was bad. Somebody had lost the check valve . Pilot jet was gunked up. Somehow it s...

Bonn · Bonn

Hi,I am new to the forum.On my last ride the splines on my gear shift shaft stripped.I would like to know what sort of job it is to fit a new shaft on my 1996 250 raid is.

Sponger · Sponger

Did a quick search and only found tyre fitting? I have a part worn tyre I need to fit as the current tyre is (I presume) an off road tyre and badly cracked. I have a load of tyre levers, happy with the refit but just wondered the best way to get the old one off? Noticed there was talk on other threads of cutting t...

tom13 · tom13

Google translator Hello gentlemen. I have a motor after refurbishment and I want to change the oil. Now it is Motul10w40 and is it good to give this one with a photo? And then do you have to rinse the engine? Is it better to pour Motul again? Thank you.

chrishughes1989 · chrishughes1989

I have recently fitted new rings and stem seals and i took it for its first ride out since the work, i did 45 miles at a steady pace. Bike sounds good and doesn't smoke anymore. When I got home I noticed that some oil had come out of the blocked off pipe on the oil breather (at the bottom), what can cause this?...

honda15i · honda15i

mine on idle or high revs makes up to 13.5v. i tried changing rectifier with no change i.e. v doesnt increase. i measured between connected battery terminals. On my other biked I looked for voltage was higher than 14v on idle.

Michael10101010 · Michael10101010

Alright so stopped by a mates house to pick something up, killed the bike grabbed what I needed, went to start again, no E start, fair enough, gave it a hellofa lott kicks, nothing, long story short I’m getting no power to the starter and no spark, dash lights work fine, horn, headlights, battery is fine...

chrishughes1989 · chrishughes1989

I have a leak from under this where there is a diaphragm. Where can I get hold of the gaskets and seals? a link or advice would be much appreciated Thanks, Chris

sidecars48 · sidecars48

Hi I recently bought lower shock BEARINGS, linkage, and swingarm BEARINGS. They say 99-06 mine is 07 model but I guess all models from 99 onwards are the same??

chrishughes1989 · chrishughes1989

http://totallyttrs.com/epages/699105d9-e4cc-4b32-b236-84e72cd67f84.sf/en_GB/?ObjectID=1718328

chrishughes1989 · chrishughes1989

after putting a new timing chain on my ttr250 2004 model as it was stretched, and it has been starved of oil on the head due to the blanking bolt being left in (sounds nice running still) I thought that maybe the excess heat on the valves and cams had killed the stem seals ( but it doesn't smoke much on sta...

TTRfan · TTRfan

What the man from Michelin says

South307 · South307

When start the engine or turn off the engine I can hear some metal knocking sound once or twice while starting and once while turning off. Is it how it suppose to be or is it something wrong? How to fix? Please advice. TTR 2008. Seems like sound comes from electric starter area.

rdchair · rdchair

Hi . I have a uk 04 bike with the plastic headlight. Has anyone done the B4 halogen bulb upgrade? Does it work or does it melt the lense? cheers

Petey4020 · Petey4020

Has anyone successfully fitted a speedo sensor to the front wheel on a 1996 white tank. I want to free up the front sprocket area for cleaning afyer my green laning adventures.

South307 · South307

Hi Guys, Recently bought TTR250 2008 (17k kms) and noticed a small oil leaking from the left corner of the bottom gasket. My mechanic recommended me to just to leave it as it is if it won't get worse and look after the oil level. It's fine for me but still a bit annoying. Any clues apart just leave it as it is?...

Ross · Ross

Hi Guys Halfway through my ride yesterday i noticed the speedo had stopped working I havent looked yet but suspect the cable. Its a blue 54 plate TTR with a analogue speedo. Any ideas before i start pulling things apart! Thanks Ross

052rtt · 052rtt

Hello, I was doing some maintenance on my ttr, when I noticed the back wheel has a lot of drag .I can spin it by hand but as soon as I stop spinning the wheel stops. Any thoughts? Thanks

chrishughes1989 · chrishughes1989

I have a removed the side case and cleaned out the gause and it was full gasket or some other type of plastic (needs new cam chain and maybe slide rubbings) I could do with some info on the following:- Here is a video with the nut cracked below the filter housing. https://db.tt/iO2UF2r8xU How much o...

Sponger · Sponger

Afternoon all, After initially attempting to replace what I thought was a leaking head gasket (turned out to be the decompressor plug) I now have the top end of my TTRs engine off and sat on the bench, to be honest the whole engine is sat on the bench after I thought it would be easier to give it a spruce up a...

TbirdX · TbirdX

And so the questions start

First air cooled bike, well, apart from an old TS100 many moons ago that I never even gave a second thought. Anyhoo, being air cooled should I switch off rather than idle for a prolonged period? Not that I sit for hours but whats the general consensus. Also, I'm hoping for a...

Jordandenton · Jordandenton

Currently riding my ttr through Turkey and the starter motor seems to have developed a fault. It seems sluggish turning the engine over 2 or 3 times makes a clunk then stops. The bike started fine thus morning and this fault has only started today. The last time I tried a small amount of smoke appeared fr...

Dan-in-a-Van · Dan-in-a-Van

It's nearly time to splash out on a chain & sprocket set, but my TTR has had Takasago Excel rims fitted and I'm not sure if the hubs are still standard. Does anyone know what the PCD of a standard TTR sprocket is? Or let me know if the sprocket in the photo looks right, I guess not if the wavy brake disc isn...

mallywoods · mallywoods

Hello all again. My beloved TTR which i have spent days cleaning and servicing and vowed never to get dirty is wearing my patience. With no notice when the starter button is pressed all i hear is a buzzing noise from the starter, all was fine last time it was used, the battery shows 12.6V on a meter and conn...

tom13 · tom13

translate google from polish. I have a refurbished engine in the workshop and a new carburettor. Is it possible that the fuel level may be bad in a new carburettor? I can not start kicking the starter. Thank you for your help

bluedream · bluedream

The cover is broken, the thing still on but doesn't look very trustworthy. Is there aftermarket or alternatively fitting parts from other models? Mine is a 2001. Google wasn't of much help sofar

scotty · scotty

HellO I have a 2003 TTR 5000 miles very little use from new. I had an oil leak dripping on the exhaust ...I have replaced the decompressor seal. It is not that. Would it be possible that the rings have gummed up and caused back pressure in the crankcase, that causing oil to leak through the head gasket? Th...

Rydasc6102 · Rydasc6102

i am having trouble cleaning the sub frame on the right side near the fender (see picture). Is there anyone who has found a way to get all of the mud and water out of this area. I don't want water to sit and rust the frame. Thanks

leigh · leigh

Hello team TTR Went for a ride last week for 4 days with my new bags on the ttr - I'll put up a trip report very soon. Long story short it went perfectly - except the exhaust side of the bike the bags got hotter than I'd like - hot enough to just start to melt one of my dry bags. I had some heat shields on the ex...

Topic		Started By	Replies	Views	Last Post
	Recently acquired 1993 TTR open enduro (Preview) Hi Totally TTR, I have recently bought a 1993 ttr 250, it's a bit rought looking and upon closer inspection the bike has revealed its rough life. Rant incoming, TL;DR at the bottom. I have a few questions about whats what on the bike, OEM parts, aftermarket replacements and bits that stood out as sketch...	BikerMat	7	2479	Aug 2, 2018 by mossproof
	New to Me TTR - some questions (Preview) I've had a few bikes before and generally do my own wrenching. Decided to pick up a dirt bike after leaving road bikes a couple years ago. Paid 900 bucks for this 1999 TTR. The Carb was a basket case. Accelerator pump was bad. Somebody had lost the check valve . Pilot jet was gunked up. Somehow it s...	Rooster	3	1032	Jul 31, 2018 by tom13
	Gear shift shaft (Preview) Hi,I am new to the forum.On my last ride the splines on my gear shift shaft stripped.I would like to know what sort of job it is to fit a new shaft on my 1996 250 raid is.	Bonn	5	1349	Jul 26, 2018 by petenz
	Tyre removal (Preview) Did a quick search and only found tyre fitting? I have a part worn tyre I need to fit as the current tyre is (I presume) an off road tyre and badly cracked. I have a load of tyre levers, happy with the refit but just wondered the best way to get the old one off? Noticed there was talk on other threads of cutting t...	Sponger	1	902	Jul 23, 2018 by Sponger
	Motul / Castrol Power1 (Preview) Google translator Hello gentlemen. I have a motor after refurbishment and I want to change the oil. Now it is Motul10w40 and is it good to give this one with a photo? And then do you have to rinse the engine? Is it better to pour Motul again? Thank you.	tom13	7	1296	Jul 22, 2018 by tom13
	oil coming from blocked off pipe below oil breather (Preview) I have recently fitted new rings and stem seals and i took it for its first ride out since the work, i did 45 miles at a steady pace. Bike sounds good and doesn't smoke anymore. When I got home I noticed that some oil had come out of the blocked off pipe on the oil breather (at the bottom), what can cause this?...	chrishughes1989	7	1342	Jul 21, 2018 by chrishughes1989
	What is good voltage coming from generator? (Preview) mine on idle or high revs makes up to 13.5v. i tried changing rectifier with no change i.e. v doesnt increase. i measured between connected battery terminals. On my other biked I looked for voltage was higher than 14v on idle.	honda15i	6	693	Jul 18, 2018 by TTRfan
	Help TTR is being real weird! Electrical problems noidea (Preview) Alright so stopped by a mates house to pick something up, killed the bike grabbed what I needed, went to start again, no E start, fair enough, gave it a hellofa lott kicks, nothing, long story short I’m getting no power to the starter and no spark, dash lights work fine, horn, headlights, battery is fine...	Michael10101010	13	1102	Jul 16, 2018 by TTRfan
	CARB GASKET (Preview) I have a leak from under this where there is a diaphragm. Where can I get hold of the gaskets and seals? a link or advice would be much appreciated Thanks, Chris	chrishughes1989	2	689	Jul 1, 2018 by ttr steve
	BEARINGS (Preview) Hi I recently bought lower shock BEARINGS, linkage, and swingarm BEARINGS. They say 99-06 mine is 07 model but I guess all models from 99 onwards are the same??	sidecars48	1	751	Jun 27, 2018 by TTRfan
	after market gaskets (Preview) http://totallyttrs.com/epages/699105d9-e4cc-4b32-b236-84e72cd67f84.sf/en_GB/?ObjectID=1718328	chrishughes1989	2	664	Jun 26, 2018 by JOHNYBOY
	Smoking at high RPM stinks of burning oil (Preview) after putting a new timing chain on my ttr250 2004 model as it was stretched, and it has been starved of oil on the head due to the blanking bolt being left in (sounds nice running still) I thought that maybe the excess heat on the valves and cams had killed the stem seals ( but it doesn't smoke much on sta...	chrishughes1989	5	997	Jun 24, 2018 by mossproof
	Inner tube valve fitment (Preview) What the man from Michelin says	TTRfan	1	730	Jun 24, 2018 by JOHNYBOY
	Strange metallic sound while starting/turning off (Preview) When start the engine or turn off the engine I can hear some metal knocking sound once or twice while starting and once while turning off. Is it how it suppose to be or is it something wrong? How to fix? Please advice. TTR 2008. Seems like sound comes from electric starter area.	South307	13	1621	Jun 20, 2018 by Cubber
	B3 bulb upgrade to B4 anyone (Preview) Hi . I have a uk 04 bike with the plastic headlight. Has anyone done the B4 halogen bulb upgrade? Does it work or does it melt the lense? cheers	rdchair	1	775	Jun 19, 2018 by ttr steve
	Retro fit wheel speedo sensor to wheel on 1996 TTR (Preview) Has anyone successfully fitted a speedo sensor to the front wheel on a 1996 white tank. I want to free up the front sprocket area for cleaning afyer my green laning adventures.	Petey4020	8	822	Jun 19, 2018 by ttr steve
	Small Leaking (Preview) Hi Guys, Recently bought TTR250 2008 (17k kms) and noticed a small oil leaking from the left corner of the bottom gasket. My mechanic recommended me to just to leave it as it is if it won't get worse and look after the oil level. It's fine for me but still a bit annoying. Any clues apart just leave it as it is?...	South307	2	670	Jun 15, 2018 by South307
	Speedo Stopped Working (Preview) Hi Guys Halfway through my ride yesterday i noticed the speedo had stopped working I havent looked yet but suspect the cable. Its a blue 54 plate TTR with a analogue speedo. Any ideas before i start pulling things apart! Thanks Ross	Ross	4	1501	Jun 13, 2018 by Ross
	Rear wheel drag (Preview) Hello, I was doing some maintenance on my ttr, when I noticed the back wheel has a lot of drag .I can spin it by hand but as soon as I stop spinning the wheel stops. Any thoughts? Thanks	052rtt	5	761	Jun 13, 2018 by 052rtt
	Oil feed issue need help please (Preview) I have a removed the side case and cleaned out the gause and it was full gasket or some other type of plastic (needs new cam chain and maybe slide rubbings) I could do with some info on the following:- Here is a video with the nut cracked below the filter housing. https://db.tt/iO2UF2r8xU How much o...	chrishughes1989	14	892	Jun 11, 2018 by chrishughes1989
	Cleaning up engine top end? (Preview) Afternoon all, After initially attempting to replace what I thought was a leaking head gasket (turned out to be the decompressor plug) I now have the top end of my TTRs engine off and sat on the bench, to be honest the whole engine is sat on the bench after I thought it would be easier to give it a spruce up a...	Sponger	11	801	Jun 11, 2018 by Sponger
	Idling and Range (Preview) And so the questions start First air cooled bike, well, apart from an old TS100 many moons ago that I never even gave a second thought. Anyhoo, being air cooled should I switch off rather than idle for a prolonged period? Not that I sit for hours but whats the general consensus. Also, I'm hoping for a...	TbirdX	4	908	Jun 11, 2018 by z1g
	Starter motor issue (Preview) Currently riding my ttr through Turkey and the starter motor seems to have developed a fault. It seems sluggish turning the engine over 2 or 3 times makes a clunk then stops. The bike started fine thus morning and this fault has only started today. The last time I tried a small amount of smoke appeared fr...	Jordandenton	8	1045	Jun 8, 2018 by Jordandenton
	Rear Sprocket PCD (Preview) It's nearly time to splash out on a chain & sprocket set, but my TTR has had Takasago Excel rims fitted and I'm not sure if the hubs are still standard. Does anyone know what the PCD of a standard TTR sprocket is? Or let me know if the sprocket in the photo looks right, I guess not if the wavy brake disc isn...	Dan-in-a-Van	4	643	Jun 7, 2018 by TTRfan
	Starter motor buzz (Preview) Hello all again. My beloved TTR which i have spent days cleaning and servicing and vowed never to get dirty is wearing my patience. With no notice when the starter button is pressed all i hear is a buzzing noise from the starter, all was fine last time it was used, the battery shows 12.6V on a meter and conn...	mallywoods	4	696	Jun 6, 2018 by mallywoods
	I can not start kicking the starter. (Preview) translate google from polish. I have a refurbished engine in the workshop and a new carburettor. Is it possible that the fuel level may be bad in a new carburettor? I can not start kicking the starter. Thank you for your help	tom13	2	677	Jun 5, 2018 by tom13
	swing arm chain guide took a beating (Preview) The cover is broken, the thing still on but doesn't look very trustworthy. Is there aftermarket or alternatively fitting parts from other models? Mine is a 2001. Google wasn't of much help sofar	bluedream	1	651	Jun 3, 2018 by TTRfan
	Possible head gasket advice needed. (Preview) HellO I have a 2003 TTR 5000 miles very little use from new. I had an oil leak dripping on the exhaust ...I have replaced the decompressor seal. It is not that. Would it be possible that the rings have gummed up and caused back pressure in the crankcase, that causing oil to leak through the head gasket? Th...	scotty	2	847	Jun 3, 2018 by scotty
	Frame cleaning (Preview) i am having trouble cleaning the sub frame on the right side near the fender (see picture). Is there anyone who has found a way to get all of the mud and water out of this area. I don't want water to sit and rust the frame. Thanks	Rydasc6102	1	621	Jun 1, 2018 by Moo
	New exhaust for my bike - need some recommendations/help (Preview) Hello team TTR Went for a ride last week for 4 days with my new bags on the ttr - I'll put up a trip report very soon. Long story short it went perfectly - except the exhaust side of the bike the bags got hotter than I'd like - hot enough to just start to melt one of my dry bags. I had some heat shields on the ex...	leigh	35	2250	May 31, 2018 by leigh
«First < 1 … 20 21 22 23 24 … 66 > Last» \| Page of 66 sorted by