It's a pretty simple operation. Just follow this step by step pictorial guide.Tools needed:- wheel-nut spanner (24mm), socket set, hammer and drift.Part needed: Yamaha part number: 10-4GY-22151-00-00 : SEAL, GUARD or an after-market item available here Clear a space and get the bike up on a stan...
hey i fitted a new set of front brake pads but now i feel like they are a two tight fit. i did grees the caliper pistons but feel lyk thy are not very responsive to go back in. any ideas whats the reason?
During my resto the top yoke nut has gone awol. Probably weighs about 1kg at the bottom of the platers tank all my fittings went to. Anyone got a spare? Part no is 90179-24542 and is number 8 on the exploded diagram. Cheers FS.
Hello all. I just joined this forum though I have been referring to ttr250.com for advice all the time. I bought my 96 TTR OE on February 2010, it is also my first bike. As my riding developed I wanted to sell it to upgrade but then couldn't get myself to let it go. After riding it for longer time I decided th...
Hello out there, Like to introduce myself. Had several Enduro models varying from 250 to 600cc. All of them four-stroke except for one, namely a KTM 250. I'm not so keen on watercooled engines and pistons that have, nearly, the same servicelife as for twostroke. Before i owned a TT350, was a nice mach...
Hello all, i've got question for you, would ttr 93 raid silencer fit to my 96 open enduro model? Are all electric wires interchangeable? How about handles for passenger? I've just bought an incomplete ttr and i'm looking for parts. Thanks, sorry for my english
Went out for a ride with a group of fellas from the ADV Rider forums today down to bull creek across the range then through the southern fleurieu and onto Deep Creek National Park. The little TTR had a lot of fun trying to keep up with 2 x 1200GS's, 1 x 850GS, 1 x KLR 650 and 2 x DR 650's. Great ride, punched out...
Just bought this sweet little bike from TTRfan. Tried my hardest to get it muddy but the lanes are frozen and the bike is so shiny nothing sticks to it! Must try harder In cow muck [IMG]https://i167.photobu...
Afternoon all,In the FAQ section there is the following advice...Uncorking the TTR250 Two freebie mods to start with: 1. Look under the tank at your throttle linkage and you will notice that Mr Yamaha installs a stop screw that limits you to less than full throttle. Adjust the screw to allow full trav...
Just to let everyone know tbec have an enduro at stourport on the 15th April day members are welcome and you can get a day licence too. For more info go to www.tbec.co.UK and all details are on the events page. Come on and give those ttrs a real workout. Hope to see you there . Keith .
Hi Guru's, After changing oil, plug (with new double stalk plug), adjusting ,mixture to the 2 turns, the TTR is still breaking down when the revs get up there. I'm getting a lot of soot out of the exhaust (1/2 of my Learner Plate is black!). I'm at 2 minds whether to attack the carby with a rebuild or tackle...
I have a 2008 which has been standing. I have cleaned the carb 5 times and am sure there is NO dirt left. Its completely stock with 4000km on the clock. Starts without the choke when cold which I think is a problem.. Then if I take it for a ride , it pulls hard and clean through the gears until I engage 6th , then...
Today I made a disappointing discovery. You may have seen my thread on a seized speedo drive. I have resolved that and have some 3-tab washers en route from Brian. I have now found that these will be of no use as the bits on the hub that should cause the washer to spin are not present, obviously broken off at...
hi all i'm new to the ttr250 having only done 200 miles on my new to me 2003 model, the problem is that when i'm riding and change gear theres sometimes a little chirrup or squeal, ive checked the cable which is lovely and smooth ive also checked the drive sprocket and chain and all appears fine. the bike ha...
Hi to the TTR clan! Well I'm the proud owner of a trusty 98 TTR Open Enduro.. Cost $1550 off the trading post (same publication that I found the wife.... but that is another story ) Since then I have had the forks resealed and oiled(on the bike, not the wife), the rear shock rebuilt (thanks to Hoey Racing in...
Hey! Greetings from Australia. Looking forward to being part of the community. Pic would be here but.. bike not in one piece at the moment, hopefully soon. Cheers mate
Hi, Out of interest before I change my original 1994 Raid gearing (14:48) to new shiny bits from Totally TTRs (13:48) I decided to obtain an acurate GPS measured top speed. I got my Tom Tom wedged in the instrument gap and drove on a bypass near me which has about 2 miles between roundabouts, straight and...
Here is my TTR250 for sale. It was first pre-registered in May 2004 by a dealer, and sold to a friend of mine in Jan 2005 with miles. Steve picked up an injury which meant he barely used it. I bought it in July 2010 with 1347 miles. It's currently done 6020 miles.Condition wise, see the photos. Ordina...
hi guys, awesome to be here. Thank god this forum exists,
Just purchased my first ever motorbike the other day and it just happens to be a TTR250 1997 Open Enduro.... It's a ripper, although the bum is a bit saggy and the front end wobbles a lot it's now my interim trusty demon until the new Tene...