A forum for owners of Yamaha TTR250 trail and enduro bikes!

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Base Gasket issues


Super Guru

Status: Offline
Posts: 8557
Date:
Base Gasket issues
Permalink  
 


I have always fitted the Cometic base gaskets dry and not had any leaks.

The manual seems to suggest fitting the OEM gasket dry also.

Brian



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Super Guru

Status: Offline
Posts: 2644
Date:
RE: Base gasket gasket
Permalink  
 


Hi Howard

If you have some marks/ scratches maybe wouldn't hurt to add a very fine smidge of non hard setting  sealant, think Bri has suggested some loctite on the crankcases Loctite 574? I believe?

Hope that helps.

Parts are on their way tomorrow

Cheers

Steve



__________________

totallyttrs.com

 



Super Guru

Status: Offline
Posts: 8557
Date:
Permalink  
 

If you do use sealant, an old trick is to put it just on the barrel side of the gasket and smear grease on the crankcase side such that if, God forbid, you have to take it apart in the future, the gasket will come away whole sticking to the barrel wink



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Veteran Member

Status: Offline
Posts: 33
Date:
Permalink  
 

Hi Brian and Steve, went with a tiny amount of sealant on the barrel just to seal the imperfections and left the crankcase side dry. Hopefully if I keep my breathers clear, I'll get no cheeky leaks.

On another note, the circlips that came with the piston pin had little tangs on one end of the ring. I was always told that the small cutout in the gudgeon pin circlip grooves (to aid removal on the pin clips) was to be kept free of the circlip ends. But with these particular clips, you can't help but to seat the tang in the cutout. Does this sound right?

Looking forward to the new parts Steve, especially the shorty header pipe. Hope that helps this 325 kit breathe!

__________________


Senior Member

Status: Offline
Posts: 422
Date:
Base gasket and sealant?
Permalink  
 


Hi All

Got a question about replacing base gaskets on these bikes. 

Mine started leaking on my first ttr some time back, replaced it and wasn't overly happy with the surface of the barrel once I spent hours taking the old gasket off. Anyway, after about 4000klms it started leaking again. 

That bike was written off (still have it) and my new TTR, that I bought from a friend and he had a professional mechanic, do a top end rebuild, new piston etc. about 1000k prior to me buying it now has a hint of a weep of oil at the base gasket. 

So at some point I will be doing it again. On both motors, it seems. 

I think sealant is needed and would use 3 bond like they do OEM on the cases etc. 

 

Question is should I apply it both sides of the gasket?

 

Cheers Leigh.

 

 



__________________


Super Guru

Status: Offline
Posts: 8557
Date:
Permalink  
 

Hi Leigh

I am not a fan of sealants and only ever grease gaskets (both sides) in the vain hope that they stay in one piece on any future tear down biggrin

A mate who doesn't like to take any chances always uses Wellseal on everything but it's a bit expensive! Example here.

I confess to using sealant on my BSA A10 though and I use Blue Hylomar on one side of the chain case gasket and grease on the other so it stays in one piece when the cover is taken off - usually....

It is unusual for TTR head gaskets to blow and there is usually something "fixable" that causes it.

I had it happen twice on one engine before I realised that the front LH head bolt wasn't torquing down on the head but binding on its threads. The solution was to run a thread cleaner down the crankcase holes and spin the head bolt in and out until it ran totally free.

Also, where a base gasket has leaked, the RH front bolt hole can fill up with oil and, if my memory serves me correctly, it is a blind hole so make sure there is no oil in it before fitting the bolt else it will hydraulic.

Good luck!

Brian

 

 



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Super Guru

Status: Offline
Posts: 1379
Date:
Permalink  
 

I use a very fine smear of flange sealant on both sides of the base gasket. I would rather spend time cleaning the surfaces much later than have a leak sooner.

__________________


Super Guru

Status: Offline
Posts: 1065
Date:
Permalink  
 

silicone & such sealants drop into oil & block oilways mr honda yamaha etc did not use them clean up the surfaces just my opinion john

__________________


Senior Member

Status: Offline
Posts: 422
Date:
Permalink  
 

All good points gentleman

I recently removed the clutch side engine cover and the gasket took hours to get off and again, using a razor blade and brake cleaner and summoning the patience of mother Teresa it still left a less than smooth surface. The gasket sealed and no leaks but wonder if I am doing something wrong? Just seems to easy to score and mark the aluminum surface. I just think how many times can you do this before the surface is really stuffed. But then gasket sealant would sort that nicely you would think? I'm dreading it as I need to remove again to adjust or replace the clutch on this new TTR so it's like, how many times can I do this before the surface is ruined.



Removing gasket sealant is way easier (in past experience) than these gaskets that seem to get superglued down. I like the idea of using grease both sides thats gotta help in removing it but I really like the idea of using sealant with gasket and doing the job once.

I think most (and I have in the past) use way too much sealant and it squeezes out and can cause problems (I guess) as you say Jonyboy. I feel if you use a fine amount, there is minimal chance of that occurring. Mr Yamaha certainly uses it on the cases though, and I know 3 bond is used OEM by most bike manufacturers so feel confident in using it.

Can only experiment I guess, but next time I do this I will use a fine amount of sealant both sides of the gasket as you say Mossproof and hedge my bets.

Do you smear it on the gasket itself, or the metal surfaces? Prob doesn't matter.

Cheers Leigh

__________________


Senior Member

Status: Offline
Posts: 422
Date:
Base Gasket issues
Permalink  
 


Hey peeps

 

So, a few years ago my TTR started leaking from the base gasket. I stripped the motor and replaced it, it started leaking again after around 4000klms or so. When pulling the original gasket off you could see it had a split or maybe had been pinched on install. I wasn't that happy with the prep I did and the mating surface of on the barrel after scraping the old one off, it leaked again and I figured I'd just not done a very good job. 

That TTR was written off before I fixed it again. 

 

Enter new TTR - this had a top end rebuild just before I bought it from a reputable mechanic. Fast forward about 3000 odd klms from me and it has started leaking again. Different motor than before and different mechanic (not me!) 

 

Crankcase is venting fine on both motors, so I've ruled that out as a possible cause. I'm about to re-do the base gasket in the current TTR and will be using 3M sealant as well this time on both sides of the gasket. I'm sure that will prevent this happening again. 

 

However in the interests of not having to do this again for a while, I thought I'd check in here to see if anyone else has struck this? Thoughts around a common reason for this happening?

Our local Yamaha dealer parts guy, told me it is common with them and they sometimes had them brand new on the shop floor leaking from the base gasket. 

 

Thoughts?

 

Cheers Leigh

 

 



__________________


Veteran Member

Status: Offline
Posts: 97
Date:
Permalink  
 

Hello,

Was the cylinder o-ring and base gasket replaced with Yamaha OEM parts?

If so, then it sounds like warping due to overheating or frequent and prolonged cold water quenching of the cylinder or case. 

 

cyl base.jpg



Attachments
__________________

-Jeff



Super Guru

Status: Offline
Posts: 8557
Date:
Permalink  
 

Hi Leigh

Assuming the base gasket was new and the O ring was fitted, there is another possibility that caught me out back along.

The two "outside" head bolts can be very tight in the casing threads and give false torque readings. I have had this before and blew two head gaskets before I realised what was happening. The bolts seem to thread in OK before the build but seem to seize a bit when under pressure.

It is really important to check the two outside head bolts run easily in the threads and if not run thread cleaners over the bolts and in the casing threads. They need to bolt all the way in.

Brian



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Member

Status: Offline
Posts: 8
Date:
Permalink  
 

Good evening,

 

Looking for a bit of advice. After a ride I noticed a patch of oil on the exhaust side that had been seeping out. Checked the oil and all is fine there so its not losing a lot. Looks to me that the base gasket has gone. Dry side just showing its not all the way round. 

New base and head gasket set from Totally TTR's?

please excuse the mud. Photos straight after a ride  ashamed.gif

21.jpg212.jpg

213.jpg



Attachments
__________________


Senior Member

Status: Offline
Posts: 422
Date:
Permalink  
 

That's where I get my gaskets from.

For the new base gasket I've done around 2 months ago, I've followed all the tips above and used sealant, I think sealant will be the deciding factor - we will see.

I've seen quite a few leak from that same corner, I've had 3 leak from that spot - gut feel is the gasket can be easily pinched in that spot, I'm not sure, but I was ultra careful this time and used sealant. Time will tell.

Also the side cover gasket leaking there can look like that, clean and ride on the road to find out :)

Cheers Leigh

__________________
«First  <  1 2 | Page of 2  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard