A forum for owners of Yamaha TTR250 trail and enduro bikes!

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Fitting Enjoy Mfg tank decals or graphics


Super Guru

Status: Offline
Posts: 8557
Date:
Fitting Enjoy Mfg tank decals or graphics
Permalink  
 


The tank I used here was in very good shape and I probably could have used some of the smaller and cheaper D&D tank decals but, having started to use an Enjoy Mfg decal kit on the rear mudguard, I was kinda bound in to them for the tank.

I hadn't prepared properly and there was still petrol in the tank so that had to be drained. I then power washed the tank using lots of TFR to get rid of any surface grease and petrol deposits.

The nude tank is ready to clothe once it's dried out and "breathed" a tad - so time for a cuppa biggrin

Tank 001.jpg

 

These are the tank decals I am using.

Tank 002.jpg

 

The decals are a better fit than the very first set I used on my "modernising" project but still need trimming as the bottom section that tucks under the tank is susceptible to lifting off. Also a small section at the edge needs trimming for a perfect(ish) fit as you can see in the pic below where I have put my patterns over the new decals.

Tank 003.jpg

 

The backing on the decals is very shiny and difficult to draw on even using a permanent marker like a Sharpie. The pic below shows the marked section to be cut off. You need to use a good pair of scissors to keep a clean edge on the decal.

Tank 004.jpg

 

I then gave the tank a quick rub down with dry 400 grit paper just to make sure there were no high spots or "pimples" that might show through the decal. I then wipe over with clutch & brake cleaner, to make sure the tank is absolutely grease free, and then spray it with some very diluted washing up liquid which gives plenty of time to move the decal around until its properly positioned.

Tank 006.jpg

 

If you are nervous about applying the decal then do it a bit of a time by just peeling off enough of the backing to allow a good first fix and then gradually pull back the paper pressing down as you go.

Tank 007.jpg

 

There is a sharp corner at the bottom rear of the RH side of the tank and its not possible to seat the decal properly so I just cut out a small V shape so it will sit flat.

Tank 009.jpg

 

It is then a case of carefully applying pressure to squeeze out the water and permanently fix the decal. Use a very clean cloth and a hot air gun for best effect.

And finally it should look like this:

Tank 010.jpg

 

No secret system - just be methodical and take your time.

Tank 011.jpg

Tank 012.jpg

Job done biggrin

Brian

 



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Super Guru

Status: Offline
Posts: 1721
Date:
Permalink  
 

You have done it again Brian! Great guide! smile



__________________

Pete. South Somerset, England.



Senior Member

Status: Offline
Posts: 127
Date:
Permalink  
 

TTRfan, you said "spray it with some very diluted washing up liquid

". What kind of washing liquid you mean? FOr dish washing or window or other?



__________________

learning to ride on 1993 TTR 250

Ex 1997 and 1998 Honda XR 250



Senior Member

Status: Offline
Posts: 216
Date:
Permalink  
 

Promo Image1.pngfor dishes this type allows you to move the graphic to get best fit by enabling you to slide the vinyl around on the surface of the tank once happy with position it will just dry and wipe away



-- Edited by hanzo on Sunday 26th of February 2017 09:33:02 AM

Attachments
__________________


Senior Member

Status: Offline
Posts: 127
Date:
Permalink  
 

thanks, it worked with fairy :D



__________________

learning to ride on 1993 TTR 250

Ex 1997 and 1998 Honda XR 250

Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard