A forum for owners of Yamaha TTR250 trail and enduro bikes!

Members Login
Username 
 
Password 
    Remember Me  
Post Info TOPIC: Running in new piston and rings


Veteran Member

Status: Offline
Posts: 44
Date:
Running in new piston and rings
Permalink  
 


Hello all, going to putting new piston and rings into TTR and wondered how long / running in process is?

Any advice would be great.

Cheers confuse



__________________


Super Guru

Status: Offline
Posts: 1721
Date:
Permalink  
 

500 miles is whats usually recommended.

__________________

Pete. South Somerset, England.



Super Guru

Status: Offline
Posts: 2608
Date:
Permalink  
 

There are pros and cons for any procedure on ring and piston running in. confuse

Ask this question to a group of riders and you end up with lots of different answers.

There is NO solution that suits every requirement.

Have a read of this CLICKY LINKY and let us all know what you decide on. wink

Don't forget to add what your results are and if you guess wrong we'll all know what not to do. smile

Martyn



__________________

You're never too old to learn something stupid

East Budleigh. Devon



Senior Member

Status: Offline
Posts: 268
Date:
Permalink  
 

I did about half a ride before I got bored. But then again gnarly lanes and running in don't mix too well. So I changed the oil to make me feel better.....



__________________


Guru

Status: Offline
Posts: 625
Date:
Permalink  
 

With just new rings i took it easy for about 70 miles then rode as normal.

__________________

2004 TTR250. White Brothers E series exhaust, modded airbox, rejetted, 13/48 c&s & many more mods..



Senior Member

Status: Offline
Posts: 402
Date:
Running in methods
Permalink  
 


Hi there, 

 

I know running in processes differ and it's a decisive topic but thought I'd ask.

 

I have two ttrs with two glazed barrels, one has finished being rebuilt and ready for mot and running in.

My friend who works with performance cars builds engines and runs them in on a Dyno. They are usually held under a specified load for a number of short cycles and refuse the run in on anything other than automotive mineral oil. Apparently it helps with the initial bedding in and stops early glazing to occur.

 

Has anyone tried this? I have previously on my 250 and 350 used semi synthetic and gone easy on the break in (not too easy, it still chugged up hills etc). The 250 was glazed at the end of a 15k mile trip my 350 much less. 

 

Any opinions are welcome, especially if someone has done this alternative way and regretted it. 

 

Currently one bikes ready for oil and starting :)

 

 



__________________

Thanks

Daniel Lee



Super Guru

Status: Offline
Posts: 1379
Date:
Permalink  
 

cdn.shopify.com/s/files/1/2030/3551/files/WTB.00003-B_POWERSPORTS_BREAK_IN_INSTRUCTIONS_06-23-2021.pdf

As previously posted in the 350 thread



__________________


Senior Member

Status: Offline
Posts: 402
Date:
Permalink  
 

Thanks Simon, that's great!

__________________

Thanks

Daniel Lee



Senior Member

Status: Offline
Posts: 484
Date:
Permalink  
 

Definitely do the break in with mineral oil not semi of full syn


__________________


Super Guru

Status: Offline
Posts: 8557
Date:
Permalink  
 

Interesting to see the old school approach to running in a new engine that appears in the Owners Manual - see below. However, I guess it refers to a completely brand new bike so running in gearbox gears and bearings, etc., in addition to the barrel and piston which is what most owners enquire about:

Running in procedure.jpg

 



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Super Guru

Status: Offline
Posts: 8557
Date:
RE: Running in new piston and rings
Permalink  
 


dlee22 wrote:

I have two ttrs with two glazed barrels, one has finished being rebuilt and ready for mot and running in.

My friend who works with performance cars builds engines and runs them in on a Dyno. They are usually held under a specified load for a number of short cycles and refuse the run in on anything other than automotive mineral oil. Apparently it helps with the initial bedding in and stops early glazing to occur. 


Hi Dan.

Hope you don't mind me merging your thread with an earlier on on the same subject. 

Regarding your glazed barrels, there is an interesting comment on this web page http://www.klemmvintage.com/breakin.htm  " In time, they learned that if they assembled the top ends dry, with no oil on the bores or pistons, they could avoid this initial burned on cylinder glaze.  The result was much shorter ring sealing times (because the rings didn’t have to wear through that glaze), and the absence of blue smoke from those important test drive blasts."

I realise they are talking about V8 muscle car engines but food for thought eh? For my own part, I could never bring myself to build an engine top end dry no

Brian



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Member

Status: Offline
Posts: 12
Date:
Permalink  
 

Hello,

Having just finished a 350 conversion I was looking for similar information re running in. Brian very kindly helped me out with the owners manual info. I had already found Simon's post re the Powersports break in instructions, which I have followed. The impression given in this is that there is really no requirement to do a significant amount of traditional running in. I have done around a hundred miles not going over half throttle. Do people think this is enough, or should I do more?

Any advice would be most welcome.



__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard