A forum for owners of Yamaha TTR250 trail and enduro bikes!

Members Login
Post Info TOPIC: Really annoying chain slap on Slider


Member

Status: Offline
Posts: 13
Date:
Really annoying chain slap on Slider
Permalink  
 


I wonder if the great collective can help with this please as its wearing me down a bit now !

Have a blue 2004 TTR and running the standard 14/44 sprocket setup with a new Renthal R3 chain. 

Finding I'm getting a really annoying chain slap on the upper swing arm chain slider (long green thing). 

Adjusted the chain so it is at the tight end of the spec at 35mm mid length with the rear sprocket centre/swing arm/front sprocket in line but it still does it really bad.

So yesterday I put a 50t sprocket on the back and it still does it badly.

It doesn’t do it on the overrun, just with slight throttle, not heavy throttle. 

It’s almost like it goes into a mad resonance slapping against the chain slider – I can actually see it doing it when I look down.

Any advice to improve this situation folks ?   Would a tighter chain help and how tight can I go before I run the risk of bearing damage ?  I did wonder if it was because the chain was new and bit less flexible ? 

Thanks all



__________________


Veteran Member

Status: Offline
Posts: 80
Date:
Permalink  
 

If your mixing a new chain with old sprockets they wont mesh well .
This slap is normal when a chain or sprocket getting a bit old .
Dont overtighten chain it will snap .


__________________


Guru

Status: Offline
Posts: 841
Date:
Permalink  
 

I find with my lowering link the chain hits the top roller rather than the slider (14/49 sprockets) - at exactly the same rev range, ie cruising high ish revs but low load. It's worse with luggage on if I forget to alter the spring preload. Once I was happy it was not the engine about to detonate, I managed to put up with it. Can't say whether it's better or worse with a new or old chain, but definitely DO NOT overtighten the chain - rapid countershaft bearing wear will result. Sorry I can't really offer a solution except maybe lace in a cush hub to your wheel?

__________________


Super Guru

Status: Offline
Posts: 7711
Date:
Permalink  
 

Back in the day, enduro bikes often used to have simple sprung chain tensioners fitted with polyurethane slippers or rollers.

I bought one about 10 or so years ago to test fit it to a TTR250 to see if it reduced chain slap. Maybe I need to dig it out and try it wink

However, having just Googled motorcycle chain tensioners there seems to be more user-fitting-friendly types available for very little money - see here for an example.  Anyone tried one of these on a TTR?

Brian



__________________

Exeter, Devon, UK

http://www.ttr250.com  - The one and only dedicated TTR250 FAQ! 
 

TIP: For easy viewing bookmark the "Recent Posts" view - http://ttr250.activeboard.com/p/recent/ 



Member

Status: Offline
Posts: 13
Date:
Permalink  
 

Thanks all, it does sound then like this is a common thing.

The other night I put the bike on the stand and ran it in 1st and watched the chain bouncing around, it appeared like it was sticking and this was perhaps helping the slap even though the back sprocket is new. Thinking the new chain grease may be the cause I completely degreased it. No real change. I did also tighten the chain to 25mm at maximum arc but no improvement.
I will try removing another link on the chain to bring the tyre in closer as I do have the room but if this doesn’t help I’ll just have to live with it.
Perhaps it will ease when the chain wears in and loosens up.

I have not changed the front sprocket though. So as comeragh said above I will also do this.

Thanks all

__________________
Page 1 of 1  sorted by
 
Quick Reply

Please log in to post quick replies.



Create your own FREE Forum
Report Abuse
Powered by ActiveBoard